Jacuzzi JVX300 Скачать руководство пользователя страница 3

INST 448 Jacuzzi® JVX Series Pool pump V10-17 

GENERAL 

The Jacuzzi® JVX Series Pool Pumps have a unique variable-speed AC motor combined with an energy efficient 
pump wet end.   When installed and plumbed correctly, the Jacuzzi® JVX Series Pool Pump will significantly 
reduce operating costs, lower noise levels and reduce greenhouse emissions. 
 

When you receive the pump, check the carton for damage. Open the carton and check the pump for concealed damage, 
such as cracks, dents, or a bent base. If you find damage, contact the shipper or the distributor where the pump was 
purchased. 
The pump must be placed on a solid foundation that will not vibrate, Jacuzzi® recommends bolting the pump to the 
foundation and providing adequate drainage should any leaks develop. 

 

The Jacuzzi® JVX Series Pool Pump range is available in a variety of models, with the following factory set speeds 
which offer approximate flow rates: 
 
 

Model 

Voltage 

High 

Medium 

Low 

Jacuzzi® 

JVX160 

220 VAC 

 
 

110 VAC 

72 gpm 

3075 RPM 

 

64 gpm 

2850 RPM 

49 gpm 

2000 RPM 

 

49 gpm 

2000 RPM 

40 gpm 

1325 RPM 

 

40 gpm 

1325 RPM 

Jacuzzi® 

JVX300 

220 VAC 

 
 

110 VAC 

82 gpm 

3400 RPM 

 

68 GPM 

2850 RPM 

54 gpm 

2000 RPM 

 

54 gpm 

2000 RPM 

38 gpm 

1150 RPM 

 

38 gpm 

1150 RPM 

(Flow rates based on a maximum speed at 26 feet total dynamic head). 

 
Each speed can be easily changed to suit your pool size, filter, plumbing and application.  The Jacuzzi® JVX Series 
Pool pump must be installed by a pool professional trained by Jacuzzi® to ensure it has been selected for the 
correct application, correctly installed and set up to suit your pool and its operation fully explained to you

FEATURES 

 

-

 

Continuous duty rated motor 

-

 

Timers and pump speed can be controlled using Bluetooth from compatible phones, tablets etc (JVX300 
only) 

-

 

Precision reinforced moulded high head impeller, giving extra performance 

-

 

Single piece moulded body for added strength and longer life 

-

 

Rapid priming diffuser quickly corrects loss of water flow 

-

 

Quick and easy disassembly for servicing 

-

 

Large capacity basket with easily removed ramp on lid 

-

 

Ability to adjust factory pre-set speeds for optimum water flow and maximum energy savings for your 
pool and its equipment. 
 

  

WARNING

 

Jacuzzi® JVX Series Pool pumps include PCB’s and microchips. It is necessary to turn power off completely for 10 
seconds before turning pump back on again. Some brands of chlorinators may bleed a small amount of power into the 
Jacuzzi® JVX Series Pool pump even when the pump off mode is selected. If this occurs, the Jacuzzi® JVX Series Pool 
pump may not reset correctly and may not start until power is disconnected completely. In some cases, the manufacturer 
of these chlorinators may be able to remove or change a capacitor in the chlorinator which will completely disconnect 
power to the pump when turned off. If not, a suitable chlorinator may be required to be purchased. Jacuzzi® J-SS40 
chlorinators completely disconnect power to the pump when the pump off mode is selected. 

 

 

 

Содержание JVX300

















Отзывы: