background image

Starting the Hydromassage

The J-Allure allows you to enjoy the benefits of a real hydromassage.  The hydromassage is created by the
combined action of 8 water jets (two sets of four).  The action of each group of four jets is either alternated or
pulsed.

To start the hydromassage jets, press the JETS button once (Figure 1).  This will activate the jets by alternating the
sets of four jets.  Pressing it a second time will pulse all eight jets.  Pressing a third time turns the hydromassage OFF.
While the hydromassage is in either mode, the PULSED JETS button may be pushed.  Pressing this button once will
increase the rate of the pulses from a default speed.  Pressing a second and third time continues to increase the rate
of pulsation.  Pressing a fourth time reverts to the default rate.  To stop the hydromassage in any mode, press the
OFF button or any other button.

Starting the Steam Bath

Press the STEAM start button on the display (Figure 1).  The steam function has a 60 minute cycle after which it turns
off automatically.  The steam bath can be turned off at any time by depressing the OFF button.   Do NOT operate the
steam generators without the water supply ON as permanent damage to the generators will occur.

Note: During steam bath operation, keep legs a distance of at least 3" away from the steam jets.

22

BATH OPERATION

Note:  These instructions pertain to all bath products manufactured by Jacuzzi Whirlpool Bath.   Not all
features discussed in this instruction pamphlet apply to all baths.

All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be
drained after each use and filled with fresh water by the next bather.  This is a health precaution, as these baths are
not designed to hold water continuously like pools or spas.   If you want a unit designed to continuously hold water,
see your Jacuzzi Whirlpool Bath dealer for the complete line of whirlpool spas available.

Once the bath is installed, remove any residue or foreign materials left over from construction.  Use turpentine or paint
thinner to remove stubborn stains, paint or tar.  Other dirt can be cleaned off with a mild liquid detergent on a damp
cloth.  Scrape off plaster with a wooden or plastic edge; do not use metal scrapers, wire brushes or other metal
tools, as they will damage the bath's surface.

Water Level

Close the drain and fill the bath until water is at least 2" above the highest  jet (see water line indicated in the illustration).
Do not turn on the whirlpool system at any time if the jets are not completely immersed in water.  Running the
whirlpool system when there is insufficient water in the bath could result in water spraying outside the bath area.
Running the whirlpool system without water will damage the recirculating pump.

Magic Touch

®

 Whirlpool Switch

The Magic Touch whirlpool ON/OFF switch, conveniently located on the bath, allows you to turn the whirlpool system
on and off while in the bath.  Simply push down on the switch button to turn on the whirlpool system.  To turn the system
off, push down on the button  again.

If your bath has an optional Jacuzzi Whirlpool Bath wall mounted timer, set it for the amount of time you wish the
whirlpool to operate.  Note: when you desire less than 10 minutes of whirlpool action, it is necessary to turn the timer
knob clockwise past the number 10 and then back to the desired amount.  If the whirlpool action does not begin when
the timer is correctly set, it is necessary to push the Magic Touch switch button.

2"

FILL TO AT LEAST 2"
ABOVE HIGHEST JET

W

HI

RLPOO

L

DEPRESS CENTER ON/OFF

MAGIC TOUCH SWITCH

Содержание J-ALLURE

































Отзывы: