Jacobsen LF 550 Скачать руководство пользователя

Страница: 41 / 60

MAINTENANCE 7

7.18 WHEEL MOUNTING PROCEDURE ____________________________________________

1. Remove dirt, grease, and oil from stud thread. Do not

lubricate threads.

2. Position wheel on hub and inspect to insure full contact

between mounting surface of wheel and hub or brake

drum.

3. Finger tighten all hardware then torque hardware in

criss-cross order; always tighten nuts in the top

position.

4. Check and torque daily until torque is maintained:

Front ................................ 100 ft.lbs. (135.6 Nm)

Rear................................. 85-95 ft.lbs. (115-128 Nm)

7.19 CARE AND CLEANING _____________________________________________________

Clean the mower and implements after each use. Keep

the equipment clean. Whenever possible, use
compressed air to clean mower.

1. Use compressed air to clean engine and radiator fins

(30 psi (2.1 BAR) maximum).

2. Use only fresh water for cleaning your equipment.

3. Do not spray water directly at the instrument panel,

ignition switch, controller, or any other electrical

components, or at bearing housings and seals.

4. Clean all plastic or rubber components with a mild

soap solution and warm water, or use commercially

available vinyl/rubber cleaners.

Repair damaged metal surfaces and use Jacobsen

touch-up paint. Wax the equipment for maximum paint
protection.

WARNING

Make sure the mower is parked on a solid and level

surface. Never work on a mower that is supported only

by the jack. Always use jack stands.

If only the front or rear of the mower is raised, place

chocks in front of and behind the wheels that are not

raised.

NOTICE

Do not wash any portion of the equipment while it is hot.

Do not use high pressure spray or steam. Use cold water

and automotive cleaners.

NOTICE

Use of salt water or affluent water has been known to

encourage rust and corrosion of metal parts resulting

in premature deterioration or failure. Damage of this

nature is not covered by the factory warranty.

CAUTION

Clean grass and debris from cutting units, drives,

muffler, and engine to prevent fires.

WARNING

NEVER

use your hands to clean cutting units. Use a

brush to remove grass clippings from blades. Blades

are extremely sharp and can cause serious injuries.

Содержание LF 550





























































Результаты поиска

Содержание LF 550

Отзывы:

Похожие инструкции для LF 550

Бренды по названию

Популярные бренды

Jacobsen LF 550, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LF 550

Отзывы:

Похожие инструкции для LF 550

Бренды по названию

Популярные бренды