Jacobsen Hauler 800 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 64

background image

OPERATION AND SERVICE INFORMATION

Page 2

Owner’s Manual and Service Guide

Read all of manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notes, Cautions and Warnings

rain and sun protection must be provided (Ref. Fig. 2 on
page 2). A dedicated circuit is required for the charger.
Refer to the charger manual for appropriate circuit pro-
tection. The charger may remain plugged in to the AC
outlet. To charge the vehicle, refer to the instruction
labels on the charger. Insert the polarized DC plug com-
pletely into the vehicle receptacle (Ref. Fig. 3 on page 2).

The charger will automatically start a few seconds after
plug insertion. The charger will automatically stop when
batteries are fully charged and the DC plug can be
removed to permit use of the vehicle.

Looping the DC cord through the steering
wheel when charging, serves as a good

reminder to store the cord out of the way when finished with
charging. The DC plug can be damaged by driving over or
catching the cord on the vehicle when driving away.

To reduce the possibility
of a physical hazard that
could result in an electri-

cal shock or electrocution, be sure that the charger
plug is not damaged and is inserted into a grounded
receptacle.

The power (AC) cord is equipped with a grounded
plug, do not attempt to pull out, cut or bend the
ground post.

The charging (DC) cord is equipped with a polarized con-
nector which fits into a matching receptacle on the vehi-
cle.

The power (AC) cord is equipped with a grounded plug.
Do not attempt to remove, cut or bend the ground post.

On-board Charger

The on-board charger is located under the seat on the
driver side of the vehicle (Ref. Fig. 4 on page 2). It is
wired directly to the batteries, only requiring it be plugged
into a dedicated 15 amp AC outlet to be operational.

When charging cycle is complete, replace cord around
charger handle in area provided.

If vehicle is to be charged with a non E-Z-GO
charger, refer to the instructions supplied with

the charger.

CONTROLS AND INDICATORS

Vehicle controls and indicators consist of:

•

key/light switch

•

direction selector

•

state of charge meter

Fig. 2 Proper Charger Installation

Fig. 3 Charger Receptacle Location

Provide Protection From Elements

Do Not Block Louvered Airways

NEMA 15 - 5R Grounded AC Receptacle

110 - 120 VAC. Dedicated 15 AMP Circuit

Locations outside the US and Canada: Reference
appropriate local electrical code and charger manu-
facturer recommendations for AC power requirements

Ref Pci 1

Ref Crl 1

Charger

Receptacle

Front of

Vehicle

Fig. 4 On-board Charger

!

!

Ref Obc 1

«
...
16
17
18
19
20
...
»

Содержание Hauler 800

































































Отзывы:

Нет отзывов

Похожие инструкции для Hauler 800

Бренд: XY Powersports Страницы: 259

Бренд: Rayco Страницы: 88

Бренд: TATA Motors Страницы: 180

Бренд: PRONAR Страницы: 135

Бренд: Tao Motor Страницы: 77

Бренд: Yamaha Страницы: 859

Бренд: Hammerhead Страницы: 67

Бренд: Zhejiang Xinyang Страницы: 37

Бренд: IDEAL INDUSTRIES Страницы: 18

Fourtrax TRX 250TM

Бренд: Honda Страницы: 224

Бренд: Daymak Страницы: 16

Бренд: Coleman Powersports Страницы: 45

BANSHEE YFZ350N

Бренд: Yamaha Страницы: 165

Бренд: Arctic Cat Страницы: 59

Бренд: Arctic Cat Страницы: 80

Бренд: Arctic Cat Страницы: 84

Бренд: Arctic Cat Страницы: 64

Бренд: Arctic Cat Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды