Jacobsen Eclipse 62800 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 60

background image

3 CONTROLS

en-16

3.5.2 Display Operating Hours ___________

To check operating hours when system power switch is in
the OFF position, press the center (Black) button.
Operating hours will be displayed for 1 minute.

Figure 3E

3.5.3 Start Up Screen ___________________

The Jacobsen start up screen will display for 5 seconds
when the system power switch is turned from the OFF to
the RUN position. The software version of the controllers
is displayed under Jacobsen.

Figure 3F

3.5.4 Alarm Codes _____________________

Refer to Section 7-LDU Error Codes for a complete list
of Eclipse error codes.

3.5.5 Mower Attachment Modes __________

The Eclipse mower, when in Operator Mode, has six
mower attachment sub-modes for operation. Forward
mower operation is standard for all modes.

The six modes are:

Mode 1 - 11 Blade Reel: Use this mode when 11 blade
reels are installed. Reel motor operation is enabled,
number of reel blades are set to 11, reel speed is set to
2200 rpm, and FOC is set to 0.16 in. (4.064 mm).

Mode 2 - 9 Blade Reel: Use this mode when 9 blade
reels are installed. Reel motor operation is enabled,
number of reel blades are set to 9, reel speed is set to
2200 rpm, and FOC is set to 0.196 in. (4.967 mm).

Mode 3 - Roller: This mode is used when the reels are
removed and the optional Quick Roll™ greens rollers are
installed. Reel motor operation is disabled.

Mode 4 - Verticut: This mode is used when optional
Verticut mowers are installed. Reel motor operation is
enabled, 1800 rpm reel speed, and FOC is set to 0.

Mode 5 - Spiker: This mode is used when the reels are
removed and optional spiker attachments are installed.
Reel motor operation is disabled.

Mode 6 - Other: This mode is used when 7 blade reels,
or an attachment other than those listed above are
installed. Reel motor operation is enabled, reel speed is

set to 2200 rpm, and FOC is set to 0. Number of reel
blades, and FOC must be set manually.

Hours

00000.0

JACOBSEN

XXXXXXX

Start up
screen

«
...
14
15
16
17
18
...
»

Содержание Eclipse 62800





























































Отзывы:

Нет отзывов

Похожие инструкции для Eclipse 62800

Бренд: DR Страницы: 44

Бренд: Kärcher Страницы: 12

Бренд: Simplicity Страницы: 4

Бренд: Oleo-Mac Страницы: 344

ULTRAVAC E Series

Бренд: Exmark Страницы: 9

Бренд: AS MOTOR Страницы: 36

E-Rider R85.1 Li

Бренд: AL-KO Страницы: 196

Бренд: Racing Страницы: 21

Бренд: Grizzly Страницы: 96

Бренд: MAJAR Страницы: 28

TLM530TRMS65-XP

Бренд: Toyama Страницы: 59

Бренд: Swisher Страницы: 16

Бренд: Swisher Страницы: 16

Бренд: IronCraft Страницы: 44

Бренд: Husqvarna Страницы: 16

Бренд: Husqvarna Страницы: 32

Бренд: Husqvarna Страницы: 20

Бренд: Husqvarna Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды