Jacobsen AR3 Скачать руководство пользователя страница 49

Страница: 49 / 342

3-16

4181384 First Edition

ENGINE

Thermostat

Removal and Installation

See Figures 3-25 and 3-26.

NOTE

Naturally aspirated engine shown; turbocharged engine
is similar.

Park the mower safely. (See “Park Mower Safely” on
page 1-7.)

Raise the hood.

WARNING

Drain the cooling system.

Figure 3-25

Loosen hose clamps (2 and 5) and remove hose (4)
from thermostat housing (3) and radiator/hydraulic oil
cooler (1).

Figure 3-26

Remove two screws (6) and lock washers (7).

Remove thermostat housing (8), gasket (9), and
thermostat (10) from spacer (11).

NOTE

Perform step 7 if removing the spacer from the engine.

Remove two socket-head screws (14), and remove
spacer (11) and gasket from engine (13).

Installation Notes

• Install the thermostat by reversing the order of

removal.

• Use new gaskets during installation.

Engine coolant is hot and under pressure! Allow
the cooling system to cool completely before
performing service.

Rotate the filler cap 1/2 turn counterclockwise
and allow pressure to vent before removing filler
cap.

TN1199

TN1200

Содержание AR3























































































































































































































































































































































Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды

Jacobsen AR3, Техническое руководство по ремонту

Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды