Jacobsen AR3 Скачать руководство пользователя страница 306

Страница: 306 / 342

CUTTING UNITS

4181384 First Edition

8-41

CAUTION

11. Rotate the bearing housing (4) up, so that the

shoulder bolt (10) is at the top of the adjustment slot
(11), and remove the shoulder bolt from the bearing
housing (4) and cutting unit frame (6).

12. Remove lock nut (7), screw (1), pivot bushing (2), and

wave washer (3) from the bearing housing (4) and
cutting unit frame (6).

13. Remove the bearing housing (4).

14. Remove oil seal (27) and washer (28) from the

bearing housing (4).

15. Inspect all parts for wear or damage. Replace parts

as needed.

Installation Notes

• Install the bearing housing by reversing the order of

removal.

• Install a new oil seal (27) during installation.

• Use a new gasket (17) during installation.

• Apply grease to bearing before installation. (Refer to

“Safety, Operation, and Maintenance Manual” for
grease specifications.)

• Adjust the bedknife-to-reel contact. (Refer to “Safety,

Operation, and Maintenance Manual”.)

Reel Blade

Removal, Inspection, and Installation

See Figure 8-36.

Park the mower safely. (See “Park Mower Safely” on
page 1-7.)

Remove bedknife shoe assembly. (See “Bedknife
Shoe” on page 8-36.)

Remove the non-drive side bearing housing. (See
“Removal and Installation—Non-Drive Side” on
page 8-40.)

Remove the drive side bearing housing assembly.
(See “Removal and Installation—Drive Side” on
page 8-38.)

Figure 8-36

NOTE

The tie bar may be on either side of the cutting unit.

Remove two socket-head cap screws (1) and
washers (2), and remove skid (3) from the side of the
cutting unit with the tie bar (4).

Remove four screws (7) and washers (8), and
remove tie bar (4) from the cutting unit frame (5).

CAUTION

Remove the reel (6).

Installation Notes

• Install the reel by reversing the order of removal.

• Adjust the bedknife-to-reel contact. (Refer to “Safety,

Operation, and Maintenance Manual”.)

To prevent personal injury, use caution when
working near the reel.

To prevent personal injury and damage to the
cutting edges, handle the reel with extreme care.

TN1276

Содержание AR3























































































































































































































































































































































Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды

Jacobsen AR3, Техническое руководство по ремонту

Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды