Jacobsen AR3 Скачать руководство пользователя страница 298

Страница: 298 / 342

CUTTING UNITS

4181384 First Edition

8-33

Repair—TR-3

Reel Drive Motor

Removal and Installation

See Figures 8-22 through 8-24.

Park the mower safely. (See “Park Mower Safely” on
page 1-7.)

Figure 8-22

Remove two nuts (2) and lock washers (3) from drive
motor (1).

Figure 8-23

Remove the drive motor (4), coupler (5), and gasket
(6) from the cutting unit.

Figure 8-24

NOTES

• Label all hydraulic hoses before disconnecting to

ensure correct installation.

• Plug hydraulic hoses after disconnecting to prevent

the loss of hydraulic oil.

Disconnect hose (8) from fitting (7).

Disconnect hose (9) from elbow fitting (10).

Disconnect hose (11) from motor OUT port.

NOTE

Record the location of fittings before removing to ensure
correct installation.

Remove fitting (8) from motor IN port.

Remove elbow fitting (10) from motor DRAIN port.

Disconnect elbow fitting (12) from motor OUT port.

Installation Notes

• Install the reel drive motor by reversing the order of

removal.

• Use a new gasket for installation.

• Apply grease to the yoke shaft lubrication fitting and

drive motor coupling. (Refer to “Safety, Operation,
and Maintenance Manual” for grease specifications.)

• Check hydraulic oil level. Add oil as needed. (Refer to

“Safety, Operation, and Maintenance Manual” for oil
specifications.)

TN1126

TN1181

TN1258

Содержание AR3























































































































































































































































































































































Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды

Jacobsen AR3, Техническое руководство по ремонту

Результаты поиска

Содержание AR3

Отзывы:

Похожие инструкции для AR3

Бренды по названию

Популярные бренды