Jacobsen AR3 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 342

background image

1-8

4181384 First Edition

SAFETY

1

Use Lifting Equipment Safely

!

WARNING

• Always use a lifting device with a lifting capacity

greater than the weight of the item being lifted.

• Secure the load to the lifting device using cables,

chains, or slings rated to handle the load being lifted.
Fasteners being used to connect lifting devices must
be strong enough to handle the load. Also be sure
the mounting point of load is strong enough to handle
the load.

• When using a lifting device, always connect the load

so it is balanced.

• Always use a lifting device on a hard, level surface.

• Lower the lifting device to the lowest point before

moving. Move the load slowly.

• Always support the load as soon as possible; never

leave a load suspended in mid-air.

Support Machine Securely

!

WARNING

Use Compressed Air and Air
Tools Safely

!

WARNING

• Compressed air is a useful tool when used in a safe

manner.

• Always use eye and ear protection while using

compressed air and air tools.

• When using air tools, do not exceed the air pressure

rating for the tool.

• When using an impact wrench, always use approved

impact sockets. Never use standard sockets on an
impact wrench.

• Disconnect the air supply before changing air tool

attachments.

• Never point air nozzles or air tools at another person.

• Always maintain air tools properly.

Always check the lifting capacity and condition of
hoists, slings, cables, or chains before use.
Using underrated or worn lifting components can
result in death or serious injury.

• Support the machine using properly rated

jackstands. Never work under a machine
supported only by a jack.

• Do not use wood or concrete blocks to

support the machine. Failure to properly
support the machine may result in death or
serious injury.

Always wear approved eye and ear protection
while using compressed air. Misuse of
compressed air could result in death or serious
injury.

• When using air nozzles, air pressure should

not exceed 30 psi (206.8 kPa).

• Never direct air nozzles or tools at a person.

• Never point air nozzles directly at skin.

«
...
13
14
15
16
17
...
»

Содержание AR3























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AR3

Бренд: Bad Boy Страницы: 44

Бренд: Parkside Страницы: 60

Ren-O-Thin 544837

Бренд: ryan Страницы: 23

Бренд: Jacobsen Страницы: 36

Бренд: Feider Machines Страницы: 22

Бренд: Jacobsen Страницы: 62

ZTR 5000 Series

Бренд: Dixon Страницы: 70

Бренд: Rally Страницы: 68

Бренд: Snapper Страницы: 8

Бренд: Poulan Pro Страницы: 48

Бренд: Hurricane Страницы: 24

Бренд: Bestgreen Страницы: 20

Бренд: Dixon Страницы: 13

Бренд: Wright Manufacturing Страницы: 23

Z-Force S Commercial 60

Бренд: Cub Cadet Страницы: 40

PowerSafe 30WS/S Series

Бренд: Ferrari Страницы: 17

Бренд: Ferris Страницы: 1

Бренд: Ferris Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды