background image

OPERATION    4

19

4.10 DAILY MAINTENANCE______________________________________________________

Important: 

For more detailed maintenance information,

adjustments, and maintenance/lubrication charts, see

the 

Parts & Maintenance

 manual.

1. Park the mower on a flat, level surface. Fully lower

the implements to the ground, engage parking brake,

stop the engine, and remove key from ignition switch. 

2. Grease and lubricate all points if required. To

prevent fires, wash the cutting units and mower after

each use.

a. Use only fresh water for cleaning your

equipment.

b. Do not use high pressure spray.
c. Do not spray water directly at the instrument

panel, or any electrical components.

d. Do not spray water into the cooling air intake or

the engine air intake.

FUEL

Fill mower’s fuel tank at the end of each operating day to

full mark on fuel gauge.

Always use clean, fresh, diesel fuel. Minimum

Cetane Rating 45.

Handle fuel with care - it is highly flammable.

 Use an

approved container; the spout must fit inside the fuel filler
neck. Avoid using cans and funnels to transfer fuel.

• Store fuel according to local, state, or federal ordinances

and recommendations from your fuel supplier.

• Never overfill or allow the tank to become empty. 

HYDRAULIC HOSE, OIL, AND FILTER

1. Inspect hydraulic hoses and tubes daily. Look for wet

hoses or oil spots and replace worn or damaged

hoses and tubes before operating the machine.

2. Check the engine oil and hydraulic oil at the start of

each day, before starting the engine. If the oil level

is low, remove the oil filler cap, and add oil as

required. Do not overfill.

NOTICE

Use of salt water or effluent water has been known to

encourage rust and corrosion of metal parts resulting

in premature deterioration or failure. Damage of this

nature is not covered by the factory warranty.

NOTICE

Do not wash a hot or running engine. Use

compressed air to clean the mower, engine, and

radiator fins to reduce the potential for corrosion and

moisture contamination.

 

WARNING

Never remove the fuel cap from the fuel tank, or add fuel,

when the engine is running or while the engine is hot.

Do not smoke when handling fuel. Never fill or drain the
fuel tank indoors.

Do not spill fuel. Clean spilled fuel immediately.

Never handle or store fuel containers near an open flame
or any device that may create sparks and ignite the fuel

or fuel vapors.

Be sure to reinstall and tighten fuel cap securely.

 

WARNING

To prevent serious injury from hot, high pressure

oil, never use your hands to check for oil leaks;

use paper or cardboard.

Hydraulic fluid escaping under pressure can have

sufficient force to penetrate skin. If fluid is injected

into the skin, it must be surgically removed within

a few hours by a doctor familiar with this form of

injury or gangrene may result.

!

!

Содержание 67043































Отзывы: