jaclo
industries
| 129 Dermody Street Cranford, NJ 07016
p
908.653.4433 |
f
908.653.1717
JACLO.COM
| PG 3
12/2/20
6
. USE INSTRUCTION
S
1)
When putting your hand into the sensing range, the faucet
will spray soap once ,and
when
hands
leave
the sensing
range, the faucet will no longer spray soap.
2
)
3
)
In order to avoid
a j
am
in
the soap tube,
if no use in
48H,the faucet will automatically spray soap once.
If not using for
a
long time,please clean the bottle
and liquid tube,
detailed
steps below:
(a)
Pour out all soap liquid,and clean the soap bottle until
there is
no foam in the bottle.
(b)
Press the button once after
p
utting some water into
bottle,the soap tube will quickly be filled.Then rinse the
tube until no foam.
(c)Press the button for more than 2 seconds to empty the
soap tube.
4
)Please use the special soap of electronic induction or
foam soap,no particulate impurities or flocs,otherwise
the tube will easily be jamed and lead to product failure.
7. DAILY USE AND MAINTENANCE
8. TROUBLE SHOOTING
Check the following before contacting the service center.
1. Soap does not flow when hands are placed within the
sensing range.
CAUSE
CAUSE
CHECKPOINT
CHECKPOINT
a) Suspension of power supply
b) Liquid outlet blockage
-Switch on the power
-Cleaning liquid outlet
b) Soap used up
-Add soap liquid
c) Liquid outlet blockage
-Cleaning liquid outlet
2. Soap liquid flow is not smooth
a) Soap is too thick
-Use the special soap of
electronic induction
d)
There are foreign
objects
in the
induction range
-Remove foreign
objects
e)
Filter net in the bottle blockage
-Cleaning filter net
f)
L
i
quid tube is bent
-Straighten the liquid tube
5) Debug
after
installation
(a)
(b)
(c)
In 20 seconds, according to the environment, the system
will automatically adjust sensing distance, please do
not
put any objects in front of the sensor.
Then press the button once,the soap liquid will quickly fill
the liquid tube.
At last please put hands in the induction range,the faucet
will automatically spew soap once.
c)
Filter net in the bottle blockage
-Cleaning filter net
1.
When using for the first time or changing the soap, please
press the green button on the control housing to quick fill
the
liquid soap tube.
2.
When the sensor is blocked by dirt or foam,please wipe
away using a damp cloth.
When cleaning around the
sensor,please be careful not to scratch the surface of the
sensor.
3. Do not
directly wash the faucet body with water to
avoid
accidents caused by damage to internal circuits.
4.
Please clean the nozzle and the filter net when
refilling
the
liquid soap
every time
.
If the dispenser is not used for a long time or has not been
properly maintained
, liquid soap
remaining in the tube
can
dry
out
and lead to spout
malfunction
. This
is not covered
by the product warranty. Please refer to the
following steps
for self-inspection and maintenance.
Filter net
Filter
cover
2.Check whether the liquid soap tube or pump tube is
blocked by viscous soap. If yes, pull out the tube joint
and squeeze out the viscous soap of the soap tube.
3.Cleaning foaming device
1.Check and clean the filter net of the bottle
Gently pry the filter cover with a knife
blade, then rinse the residual impurities
or viscous soap liquid in the filter net
repeatedly with clean water.
Be careful not to break the filter net
during the cleaning process.
This device is hidden at the bottom of
the faucet body.
Please be careful not to scratch the
strainer
of the
fi
lter net during cleaning.
When installing back the foam device, be
careful not to forget to install o-ring.
4.Cleaning pump tube
Pump tube
When the pump tube is blocked or adhered,
refer to the following steps to clean the tube.
1.Please gently pull out the pump tube in
the direction of the arrow on the picture.
2.Remove liquid tube joint and squeeze out
the thick soap.
3.Finally install back the joint and pull back
the pump tube in the opposite direction.
liquid tube
joint
F
ilter inlet
connector
Filter net
Filter bracket
