jaclo
industries
| 129 Dermody Street Cranford, NJ 07016
p
908.653.4433 | 800.852.3906
f
908.653.1717 | 800.852.4133
8.07.18
JACLO.COM
| PG 4
Handle Installation
1. Install handle onto stem in desired "off"
position.
2.
Confirm handle is not binding with
escutcheon. Adjust if necessary.
3. Handles are fastened with a set screw or
top screw.
Figure 7
.
4. If set screw type, screw, tighten then
press in decorative cap with o-ring.
5. If top screw type, screw, tighten then
press in decorative cap with o-ring.
FIGURE 7
COMPONENT PARTS
4
7
6
5
3
1
2
9
8
10
12
11
13
Drain Assembly
1.
Disassemble top flange (2) and drain stopper (1)
from pop-up drain body (6).
2. Loosen mounting nut (5) for desired height.
*Note: This may vary depending on thickness of
sink basin or countertop.*
3. Apply appropiate silicon/putty under lip of top
flange (2).
4. From underneath, insert drain body (6) through
sink basin or countertop and attach top flange (2).
5.
Guide sink gasket (3) & plastic washer (4) up snug
to bottom of sink basin or countertop.
6. Test the length needed for drain stopper (1) by
adjusting height of eyelet so it is visible from side
port of ball rod.
7. Align top flange (2) & drain body (6) & tighten nut
(5) securely.
8.
Test alignment using ball rod (10) without ball rod
seats (8) to ensure it goes through eyelet of drain
stopper (1).
9.
Adjust length of drain stopper (1) (if required) by
loosening the nut & eyelet to desired height. Then
secure back up to bottom of drain stopper (1).
10. Put one ball rod seat (8) before ball in ball rod (10)
concave side toward ball. Push through side port
making sure the ball rod (10) goes through drain
stopper (1) eyelet. Put second seat (8) on+to other
side of ball rod (10) & attach ball rod nut (9). Do
not over tighten.
11.
Pushing ball rod (10) down to raise drain stopper
(1) in sink. Test & adjust if necessary.
12. Attach lift rod strap (11) to pop-up rod.
13.
Push down on ball rod (10) putting one
end of spring clip (12) on, then put through
appropiate hole in lift rod strap (11). Attach other
end of spring clip (12) & test.
14.
Attach tailpiece (7) to drain body (6) using pipe
thread sealing tape on threads.
1 ½”Ø
17
15
14
16
COMPONENT PARTS
Hidden Aerator -
9880-AER
8880 Low Profile Spout -
8880-SPOUT-LL-** / 8881-SPOUT-LL-**
Lift Rod -
9880-ROD-**
Handles -
VARIES ON MODEL
Round or Square Valve Escutcheon -
VARIES ON MODEL
Valve Body Cold -
11833-0 OR 11835-0 (FOR L & C HANDLE ONLY)
Valve Body Hot -
11832-0 OR 11834-0 (FOR L & C HANDLE ONLY)
Valve Body Nut (2)
Cock Nut -
A438-0
Hose (2) -
5130-0
Washer -
PART OF SPOUT
Brass Nut -
PART OF SPOUT
Brass Nipple -
PART OF SPOUT
Brass Tee -
PART OF SPOUT
Round or Square Spout Escutcheon -
VARIES ON MODEL
17
3
5
4
16
15
13
13
13
6
17
15
14
16
4
3
A
2
18
Fiber Washer (2)
19
Hot Hose Fitting -
30823-RGH
Cold Hose Fitting -
30822-RGH
18
19
18
19
2
1
Valve Cup Washer -
VALVE CUP WASHER
9/16"
9
8
7
6
10
11
8
7
9
13
12
10
11
12
9
8
10
11
7