background image

16

PROBLEM

POSSIBLE CAUSE

REMEDY

Water overflow 

from bottom of 
door. 

1. Clogged drain.

2. Machine not level.

3. Excessive inlet pressure.

4. Detergent foaming. 

5. Wash/rinse arm end-cap missing.

6. Excessive fill time.

1. Remove obstruction.

2. Level machine or increase height to the front.

3. Install pressure reducing valve or adjust if one is present.  
Ensure flow meets data plate specification. 

4. Reduce detergent quantity. 

5. Replace.

6. Adjust timer fill time (see Initial Start-up section).

Wash motor 
doesn’t 
operate on 
delime wash.

1. Loose or broken wires.

2. Defective delime switch.

3. Defective motor starting relay.

1. Reconnect or replace wires in motor. 

2. Verify delime switch triggers input on PLC. If not, check 

wiring/replace membrane.

3. Replace.

Motor operates 
on delime 
wash but not 
on automatic.

1. Defective circuit in delime switch. 

2. Loose or broken wires.

1. Replace switch. 

2. Tighten and/or replace.

No water comes 
through the  
arm when the 
“FILL” switch is 
depressed.

1. Water not turned on.

2. Defective solenoid valve.

1. Turn water on.

2. Replace solenoid valve. 

Little or no 
water coming 
through the rinse 
assemblies.

1. Limed-up rinse heads or piping. 

2. Low water pressure. 

1. Delime rinse heads.

2. Increase pipe size to machine.  Adjust pressure 
    regulator. 

Rinse water runs 
continuously 
with breaker 

turned off.

1. Defective plunger in solenoid valve.

2. Defective diaphragm in solenoid valve.

1. Replace.

2. Replace diaphragm.

COMMON PROBLEMS

TROUBLESHOOTING

Содержание DELTA Series

















































Отзывы: