manualshive.com logo in svg

Jackson CONSERVER XL-E, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Jackson CONSERVER XL-E Скачать руководство пользователя страница 15

07610-003-92-84-R

8

INSTRUCTIONS

INSTALLATION

Before installing the 

machine

, check the packaging and machine for damage. If the 

packaging is damaged, the machine might also be damaged. If there is damage to both 
the packaging and machine, do not throw away the packaging. The 

machine

 has been 

inspected and packed at the factory and is expected to arrive to you in new, undamaged 
condition. However, rough handling by carriers or others might result in damage to the 

machine

 while in transit. If so, do not return the 

machine

 to the manufacturer; instead, 

contact the carrier and ask them to send a representative to the site to inspect the 
damage and complete an inspection report. You must contact the carrier and the dealer 
that sold you the 

machine

 within 48 hours of receiving the machine. 

While removing the machine from the packaging, ensure that there are no missing 
parts. If an item is missing, contact the manufacturer immediately. 

The 

machine

 must be level in its operating location to prevent damage to the machine 

during operation and to ensure the best results. The 

machine

 comes with four adjustable 

bullet feet, which can be turned using a pair of channel locks (or by hand if the 

machine

 

can be raised safely). Ensure that the 

machine

 is level from side-to-side and front-to-

back before making any connections.

The manufacturer does NOT endorse "Tankless On-demand" water heaters for use 
with their dishmachines.  The manufacturer DOES endorse, and highly recommends, 
the standard "Tank" style water heaters, sized to properly handle the water heating 
requirements of the facility. 

Plumbing connections must comply with all applicable local, state, and national 
plumbing codes. The plumber is responsible for ensuring that the incoming water line 
is thoroughly flushed before connecting it to any component of the machine. It is very 
important to remove all foreign debris from the water line that might potentially get 
trapped in the valves or cause an obstruction. Any valves that are fouled as a result of 
foreign matter left in the water line—and any expenses resulting from this fouling—are 
not the responsibility of the manufacturer.

A water hardness test must be performed to determine if a water treatment system 
needs to be installed.

INSPECTION

LEVELING

UNPACKING 

PLUMBING

Do not throw away the 

container if damage is 

evident!

The plumber MUST flush 

the incoming water line!

A water hardness test 

must be performed. 

FACILITY HOT 

WATER HEATER

x4

Содержание CONSERVER XL-E

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды