JAC S5 Скачать руководство пользователя страница 58

Страница: 58 / 70

S5 Workshop Manual

Engine

EM-58

9) Flange and crank chain was installed on the crankshaft Make sure that the
installation is conducted according to the instruction in figure.

Notes:

■ Pay attention to flange direction. If it is

installed in wrong direction, it may cause
belt damage.

10) Install special washer and chain wheel bolt onto the crankshaft, and tighten chain
wheel bolt.

Tightening Torque:

Crankshaft chain bolt:

160

～

170

N•m

11) Insert screwdriver into the inspection
hole of left balance shaft on the left of
cylinder body to keep the shaft stationary.

12) Install oil pump chain wheel and
tighten nut to the specified torque.

Tightening Torque

A. Oil pump sprocket:

～

N•m

13) Install camshaft chain wheel and
tighten bolt to the specified torque.

Tightening Torque

B. Camshaft sprocket bolt

～

100

N•m

EM097

EM096

EM095

EM094

Secondary chain wheel

of crankshaft"B"

Crankshaft

Chain wheel

of crankshaft

Screwdriver

www.cargeek.ir

www.CarGeek.ir

Содержание S5







































































Результаты поиска

Содержание S5

Отзывы:

Похожие инструкции для S5

Бренды по названию

Популярные бренды

JAC S5, Руководство по ремонту

Результаты поиска

Содержание S5

Отзывы:

Похожие инструкции для S5

Бренды по названию

Популярные бренды