5
Control Panel
CAUTION:
Remove fuse, or turn circuit breaker off,
whilst installing Controls and Electrics.
Select a position for the Control Panel (key 31) that
•
is convenient for both standing and seated users,
and which allows you to run the 10ft (3m) control
cable to the toilet.
To use the Jabsco Fascia Panel provided, (key 32)
•
drill a 5/8" (16mm) hole for the 6 way control cable
connector. Screw the control panel (key 31) onto
selected location with suitable counter sunk head
screws. Clip on fascia panel (key 32).
To use Gewiss fascia panels remove the four screws
•
tabs (see picture below). Cut a rectangular hole
53mm x 92mm. Fix panel (key 31) to selected
location with four counter sunk head screws. Clip on
Gewiss fascia panel.
To use Vimar fascia panels remove the four screw
•
tabs (see picture below) Cut a rectangular hole
53mm x 92mm. Place adaptor (key 33) onto panel
(key 31) and screw into place with four counter sunk
head screw. Clip on Vimar panel onto adaptor.
Slide the Heat Shrink Sleeve (key 30) over the
•
control cable. Plug in the 6 way control cable to the
toilet, and carefully use a hot air gun or hairdryer to
seal the Heat Shrink Sleeve over the 6 way
connector.
Note that the toilet has 2 other leads - Red and
•
Black. Connect your boat’s Positive (+) feed to the
Red (+) lead, and your boat’s Negative (-) return to
the Black (-) lead.
Foot-switch
Connect your boat’s Positive (+) feed to the Red (+)
•
lead, and your boat’s Negative (-) return to the
Black (-) lead.
Securing the toilet
Bolt down the base toilet ensuring that the Foot-
•
switch (key 24) and/or the blank (key 28) are located
correctly. Make sure that the cable from the Foot-
switch is located in the guide and not trapped.
With control panel fit 2 blanks, with Foot-switch fit 1
•
blank on respective side.
Before fitting the seat and lid, if required, you may
•
rotate the upper part of the toilet and offset the
angle of the seat to the base.
To rotate the top, loosen the two screws in the clamp
•
(key 4) and rotate to the desired position, retighten
clamp screws.
The top may be rotated 68° each side but, you will
•
need to fit a longer 19mm (¾”) inside diameter rinse
inlet pipe (key 15).
Testing
Ensure that the battery is fully charged, and that the
•
circuits are live.
Open both seacocks.
•
Refer to the next section - OPERATING INSTRUCTIONS.
•
To prime the Rinse pump on first installation,
•
operate the 'Quick Flush' function (for the control
Panel version several times until water flows into the
toilet bowl. The foot-switch may have to be pressed
several times until water flows into the bowl.
Safet y
Ensure that this INSTRUCTION MANUAL reaches the
owner, skipper or operator of the craft as it contains
essential safety information.
ON COMPLETION - CLOSE BOTH SEACOCKS
OPERATING INSTRUCTIONS
The toilet is one of the most used pieces of equipment
on your boat. Correct operation of the toilet is essential
for the safety and comfort of your crew and craft.
Open inlet and outlet seacock (and secondary
•
valves if fitted).
Use good quality hard or soft household toilet paper,
•
but do not use more than necessary.
CAUTION:
Do not put anything in the toilet unless
you have eaten it first, except toilet
paper.
Cut along indented lines on
either side and pull off screw
tabs
Screw into place with
four counter sunk head
screws
ELECTRICAL SPECIFICATIONS
Voltage
Amp Draw
Fuse/Breaker
Wire size mm
2
(AWG) per metre (foot) of length*
0-4 m (0-13 ft)
4-6 m (13-20 ft)
6-12 m (20-40 ft)
12-18 m (40-60 ft)
12 Vdc
20
25 amp
6
mm
2
(#
8
)
10
mm
2
(#
6
)
20
mm
2
(#
4
)
25
mm
2
(#
3
)
24 Vdc
10
15 amp
2.5 mm
2
(#1
2
)
4 mm
2
(#1
0
)
6 mm
2
(#
9
)
8 mm
2
(#
8
)
* Wire length is the total distance from the battery to the flush pump and back to the battery
