Telephone dialer TD-101 / TD-101W
- 10 -
MDJ512 10
Telephone dialer TD-101 / TD-101W
- 15 -
MDJ512
10
7. Monitoring station data sending
Function of the TD-101 including the Monitoring Station (MS) communication is demonstrated in the
diagram on page 9. Data is sent to the monitoring station before voice & Pager messages are sent (if
these messages are used). All parameters of the MS communication should be programmed in
cooperation with your monitoring service provider. Programming of the data for the MS is only possible
in the Installer mode.
If you do not use the dialer to send data to a monitoring station, do not program anything in this
section.
7.1. Opening of Installer Mode for monitoring station data programming
To enter Installer level
from Standby,
enter Installer code IC press
B
and enter Installer Code
IC again.
Factory default IC is 1010 so when you open the Installer mode for the first time, enter
B
. The installer level is indicated by the yellow LED.
All parameters are programmed in the following sequences. If the first key of the sequence is
entered, the red LED will start to flash. When the sequence is completely entered, the red LED will
turn off (data will be stored). A started sequence entering can also be terminated by pressing the
E
key at any time.
After all programming is finished, the Installer mode must be exited by pressing the
E
key (all the
LEDs will turn off). The dialer can not be activated in the Installer level !
7.2. Entering telephone numbers of the Monitoring Station
Telephone numbers can be programmed in the Installer mode (the yellow LED is ON - see 7.1.),
entering:
DDDD
...
D
M
E
where:
D
is a telephone number, keys
to
or
B
(i.e. pause). Pause can not be on the first
position, keys
and
can also be programmed in tone dialing mode. Each telephone
number can have up to 16 digits.
E
is the tel. number memory
7
= main tel. number (
Mem7
),
8
= alternate tel. number (
Mem8
)
.
The alternate number is only called if the main number is busy.
Example: The main telephone number of the monitoring station will be 811 777 :
M
7.3. Deleting of Monitoring Station telephone numbers
Telephone numbers for MS can be deleted in the installer mode (the yellow LED is ON - see 7.1.),
entering:
B
M
%
where:
%
is the memory number
7
or
8
which will be erased. If a number is erased, the corresponding
dialing will not be performed.
Note: If both numbers for MS are erased, there will be no communication to the monitoring
station
Example: Spare MS telephone number will be erased :
B
M
If Stop with
E
key is enabled, the TD-101 action can be stopped only if no input is triggered. The dialer
action is terminated a few seconds after the
E
key is pressed.
If Stop is disabled, the communication can not be stopped before its end.
Example: The STOP will be disabled :
F
8.11. Emergency triggering with
F
key
Emergency trigger key can be enabled or disabled in the installer mode (the yellow LED is ON - see
8.1.), entering:
F
D
where:
D
=
0
emergency trigger disabled
D
=
1
emergency trigger enabled
(factory default setting)
If you use the
F
key as an emergency button, you can mark the key with an adhesive label which
is included.
Note: The above setting does not have any effect to the remote control trigger of TD-101W model.
Example: Emergency trigger will be disabled :
F
8.12. Changing of the Installer Code
To avoid non authorized access to the installer mode, change the Installer Code for a new one. The
code can be changed in the installer mode (the yellow LED is ON - see 8.1.), entering:
M
DDDDDDDD
where :
DDDD
is the new installer code (four digits). The new code must be entered twice to be changed
(protection of accidental change). The original factory default setting of the Installer Code is
1010.
Example : The user code will be changed for code 3112 :
M
8.13. Duration of Pause in Pager dialing
Duration of the pause which is generated with the
F
key in pager number programming can be
selected in the installer mode (the yellow LED is ON - see 8.1.) entering.
F F
D
where :
D
=
0
pause = 5 seconds (factory default)
D
=1 pause = 10 seconds
Example: 10 seconds Pause will be selected:
F F
