The JA-62GSM communicator for GSM
The JA-62GSM communicator for GSM
4 / 11
MLD52902
6.10. Forwarding of incoming SMS messages
The communicator enables the automatic forwarding of incoming SMS
messages which contain no valid instructions to the system:
801 0
messages are not forwarded
, but the communicator saves the
last 10 received messages to the SIM card
801 1
messages are forwarded
to the first programmed tel. number in
memories M1 to M8 (e.g. if numbers are only programmed in M5
and M6, then messages will be forwarded to M5). The tel. number
from which the SMS was received will be shown at the beginning
of the forwarded text.
Factory default setting:
messages are forwarded
Notes:
−
In order to protect the user against runaway (donation SMSes etc.), the
forwarding is limited to the first 50 SMS messages. The counter can be
erased automatically each midnight, by processing any SMS instruction
or by exiting Service / Maintenance mode.
6.11. SMS instruction confirmation
If the communicator receives a valid SMS instruction, a confirmation SMS
will be sent a s a reply. This confirmation can be disabled as follows:
904 0
disabled
904 1
enabled
Factory default setting:
enabled
6.12. Reaction to incoming calls
This sequence can be used to set the communicator’s reaction to incoming
phone calls:
905 0
the communicator ignores incoming calls
905 1
the communicator will answer after ringing for 15s
Factory default setting:
answer after ringing for 15s
6.13. GSM signal dropout indication
This feature enables the monitoring of GSM network signal availability. If
enabled and if there is a GSM signal dropout longer than 15 minutes, the
control panel announces “External communication fault”.
906 0
signal availability monitoring disabled
906 1
signal availability monitoring enabled
Factory default setting:
disabled
6.14. Phone receiver loudness
To set the loudness of the receiver of the phone which is used to call the
communicator key in:
909 x
where x is a number from 1 to 9 (max.)
Factory default setting:
9 (max.)
6.15. Number to be called to maintain SIM card validity
If a prepaid SIM card is used and a lack of outgoing phone calls for a
certain period cancels the validity of the SIM card, then this function offers the
following: if there have been no outgoing phone calls within the last 90 days,
then the communicator automatically calls the number programmed by this
sequence. The communicator waits until the call is answered and then
automatically hangs up after 10 sec.
910 xx...x F0
where:
xx...x
is the telephone number
Notes:
−
To erase this number enter 910 F0
−
It is recommended to call cheap public services (e.g. weather forecasts
etc.) but not toll-free numbers.
Factory default setting:
Erased
6.16. Restriction of the number of sent SMSes
The parameter limits the amount of sent SMSes to 100 per 24 hours. 50
may be alarm SMSes and 50 may be for other events. This is to prevent
enormously high telephone fees.
803 0
restriction disabled
803 1
restriction enabled
Factory default setting:
enabled
There is also a limiter to 500 SMSes per 24 hours – it can not be
disabled.
6.17. Prepaid SIM card credit interrogation
The communicator is capable of checking the credit balance of its SIM card
upon request (by the “CREDIT” SMS instruction) or this activity can be
requested automatically (with a preset cycle) and if it finds out that the
remaining credit is lower than the preset value, an information SMS is sent.
The function is set by sending the following SMS instruction:
code_CREDIT_uu..u_xx_yyy_zz
where:
Code
is a valid access or service code for remote access
(e.g. 0000), a change of parameters is possible only
with a service code (other codes allow “0000 CREDIT“
SMS credit interrogation)
_
space
uu..u
instruction recognized by the GSM network to check
the balance
xx
automatic checking period in days,
yyy
minimum acceptable credit balance
zz
the textual position in which the number showing the
balance starts in the reply message from the GSM
provider.
Notes:
−
If the reported credit balance is lower than the set limit (yyy), text no. 545
will be sent to phone numbers M1 and M8 which have the “Low credit
balance” (event no. 28) event sending enabled
−
If only
uu..u
follows the CREDIT instruction (no xx yyy zz) then periodic
balance checking will not be performed, but the balance will be checked
immediately
−
If there is further data following the CREDIT instruction, the
communicator will memorize them and automatically put them in the
message when the CREDIT instruction is used again (i.e. the Credit
instruction must contain at least the uu..u part upon the first sending) and
the user just needs to send: code CREDIT
Example:
sending the SMS instruction “
code CREDIT
∗
101# 7 50 1
”
causes the credit balance to be checked every 7th day after the SMS has
been sent and if the balance (starting with the first character in the message
from the GSM provider) is lower than 50 currency units it will be reported.
Warning: the use of prepaid SIM cards in the communicator can
negatively influence the reliability of the device. Some GSM providers
block cards not only when there is no credit but also when they are not
topped up frequently enough. This means that even if there is enough
credit balance on the card, the communication can still be blocked. We
therefore strongly advise the use of tariff SIM cards !!!
6.18. Remote programming by SMS instructions
The communicator enables remote programming of the system by the
following SMS instruction:
code_PRG_seq_seq, another instruction
where:
Code
valid access or service system code (e.g. 0000)
_
space
seq
programming sequence usually set via the keypad
Notes:
−
Only characters which can be keyed in from the system keypad
(0 to 9, * and #) can be used in the sequences.
−
When a valid instruction is received, the communicator performs the
sequence by simulating pressing the keys on the keypad. A comma in
the SMS is taken as a pause in the sequence entering.
−
If you want to remotely reprogram the system it must first be unset and
then switched to programming mode.
−
The number of sequences in one SMS is limited by the maximum size of
an SMS in the GSM network.
Example:
by sending SMS
0000_PRG_F06060_201_#, SET 4321
the
exit delay will be set to 10s and set system by the code 4321.
6.19. Registration code
The code is stated on the label on the communicator panel but it can also
be sent to the mobile phone by SMS (see table 1, 3.3) DINFO command. To
request a registration code, enter:
911 xx...x F0
where:
xx...x
is the number of the phone where the code should be
sent
Notes:
−
The time needed for delivery of the code depends on the current GSM
network speed
−
Each communicator has a unique registration code in the following
format: xxxxx-xxxxx-xxxx
