JA-60V Wireless outdoor PIR detector
1
MEB
52101
JA-60V Wireless outdoor P.I.R. motion detector
The JA-60V is an outdoor intruder detector designed to detect human
body movement in a protected area. Used PIR detector produced by Optex
has two double-layered detection patterns (upper and lower) both have to
be activated to trigger the alarm. This reduces false alarms, particularly
those caused by temperature changes, light reflection or small animals.
A tamper triggers an alarm if there is any attempt to tamper with the
detector.
The built-in transmitter is fully compatible with all JA-6X control panels.
Specifications
Power
3 V - 2 x AAA battery 1.5V
Battery life time
about 1 year
Working frequency
433.92 MHz
RF Power
<
10 mV
Working range
max. 100 m (open area)
Specification of the Optex VX 402R detector
Detection method
Passive infrared
Coverage
12 m / 90° ; 14 segments
Mounting height
0.8 – 1.2 m
Detection speed
0.3 – 1.5 ms
-1
Battery saving timer
5 or 120 seconds
LED indicator
only in the test mode
Environmental class
IV (EN 50131-1)
Operating temperature
-20°C to +50°C
Waterproof IP54
Humidity
95%
Dimension
198 x 80 x 108 mm
Security grade
2 (EN 50131-1)
Can be operated according to
ERC/REC 70-03
Hereby, Jablotron Ltd., declares that this JA-60V is in
compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Original of the conformity assessment can be found at the web page
www.jablotron.cz, section Technical support.
Contents of the set: detector JA-60V, pole mounting kit, screw kit, area
masking plates, 2 AAA
batteries
Installation
Select the proper place for mounting the detector according to
following:
1.
Install the detector perpendicular to the ground to make upper
detection area parallel to the ground
2.
Installation height is 0.8 – 1.2 m
3.
Mount the detector so that a majority of traffic flow is across the
detection pattern
4.
Too much light such as strong sunlight directed exactly to the sensor
may cause unstable condition. It is highly recommended to avoid
such installation.
3.
1.
1.
3.
0.8
1.2 m
To open the detector:
1.
Unscrew the lock screw and remove the top cover.
2.
Unscrew the screws fastening the back box. Remove the back
box.
NOTE: never touch surface of the PIR sensor.
Fix the detector to desired place. Detector can be fixed directly on the
wall or by using supplied fix bracket on the pole (Ø 43 – 48 mm).
Optical Part
Cover
Lock Screw
Back Box
Pole Mounting
Bracket
Setting Switches
Enrollment of the detector to the receiver
The transmitter is placed below the optical part of the detector. Study
the installation manual of the receiver unit (control panel) first to learn how
enter the enrolling mode. When the receiver is switched to the enrolment
mode insert the two provided AAA batteries into the detector (polarity is
marked in the detector). The detector will generate an enrollment signal
after the batteries are installed.
INSTANT
DELAY
JA-60N transmitter
•
Use DIP switch no. 1 to select the reaction of the system:
-
instant (position ON)
-
delay (position 1).
•
Leave DIP switch no. 2 in position ON.
Adjustment
The upper detection area stays parallel to the ground. The lower area
moves as shown below depending on the position of the setting switch.
Detection length is therefore limited by the length of lower detection
area, since both upper and lower detection area have to be activated
at the same time to trigger the detector.
A
distance 0 - 12 m
D
distance 0 - 2 m
C
distance 0 - 5 m
B
distance 0 - 8 m
