JA-163A RB Wireless outdoor battery-powered siren
JA-163A RB Wireless outdoor battery-powered siren
2 / 2
MNM51103
to open a dialog window, internal setting is separated into 2 tabs:
Settings
and
PG indication
(default settings are marked *):
Settings tab:
Acoustic indication of an intrusion alarm from sections:
to set for
which sections the siren should indicate an alarm, as well as setting
the chirps. The default setting is indication for all sections disabled.
Reaction:
defines whether the siren should indicate
EW*
(external
warning) or
IW
(internal warning). Alarm indication can also be disabled
completely (other functions remain enabled).
Siren sound:
intermittent*, continuous. Option
intermittent
saves energy.
Maximum siren time:
No, 1, 2, 3*, 4, 5 minutes, During an alarm.
Option ‘No’ – the siren doesn’t indicate alarm acoustically (optical indication
remains). Option ‘During an alarm – acoustic indication in duration of ‘Alarm
length’ set in ‘Parameters’.
Note: the maxim Alarm length is 20 minutes,
which would significantly affect the battery lifetime
.
Different fire alarm indication:
YES/NO*: if enabled the siren indicates
fire alarm by fast loud beeping, not by a standard beeping when indicates
other types of alarm like intrusion, sabotage, panic ,etc. (fast beeping
indicating the fire alarm is synchronized with the acoustic indication of the
fire detectors)
Enabling any of these mentioned options can
cause a reduced battery life-time depending
on the frequency of its use. That´s why
we recommend fitting the BAT-100A second
battery.
Other acoustic indication from section:
selection of the sections
for which sounds mentioned below will be produced. Default setting
is ‘All sections.
Higher volume:
YES / NO* - affects only entrance / exit delay indication
and sounds indicating PG output triggering. It doesn´t have any influence
on the sound of an alarm.
During section control:
YES / NO – if enabled, the siren chirps once
after setting, twice after unsetting and three times when unsetting after
an alarm.
During warning:
YES / NO* - When enabled the siren will beep three
times to indicate:
1) inability to set (a system status which prevents setting, such as
a fault or a triggered detector)
2) unsuccessful setting (an event occurs during exit delay, e.g.
a triggered detector)
3) unsetting with alarm memory (an alarm occurred)
Entry delay:
YES / NO* if enabled, it indicates the entrance delay
for the whole entrance time – intermittent beeping.
Exit delay when partially set:
YES / NO* - if enabled, it indicates
the entrance delay for the whole time when the system has been partially
set – intermittent beeping. This option is available when
Entry delay
is enabled.
Exit delay:
YES / NO* - if enabled, it indicates the exit delay for
the whole exit time when the system is fully set – intermittent beeping.
Upon loss communication
: YES / NO - When enabled, the siren
sounds in case of loss communication with the control panel longer than
(110 min). The length of sounding depends on ‘Maximum siren time’
– where the option ‘During an alarm’ signifies 20 minutes.
Optical indication:
Flashes every 60 seconds:
YES / NO* - It sets to one siren flash per
minute. It can be used as a warning that the building is protected by
an alarm system.
During warning:
YES/NO* - if enabled, the siren indicates by triple
flashing:
1) inability to set (a system status which prevents setting, such as
a fault or a triggered detector)
2) unsuccessful setting (an event occurs during the exit time, e.g.
a triggered detector)
3) unsetting with alarm memory (an alarm occurred)
When controlled by a section:
YES / NO* – it sets a siren to optically
indicate setting and unsetting of (a) section(s). It blinks once when set and
it blinks twice when unset and when unset after an alarm then three blinks.
LED indication:
red*/ blue, sirens are equipped with dichromatic LED
indicators. According to the colour of the bought front cover
it is necessary to set the same colour of indication for LEDs.
Siren flashing options:
During alarms*/ 1/ 3/ 5/ 30/ 60 min of flashes
after an alarm. This option can set the length of siren flashing for only
the alarm time or extended for by a pre-set interval. Extended flashing can
be terminated by new system setting or cancellation of alarm indication in
the system (with a keypad).
Periodical communication:
1 s / 8 s – This parameter can set
the maximum postponed reaction of the siren to an alarm, supplementary
indication or Signalling PG.
Notes:
PG output activation sometimes might not be indicated when periodical
communication is set to 8 s and a PG output is switched ON for
a shorter time than 8 s.
If the end customer wants any of the supplementary indications
mentioned above, we recommend to set the ‘Periodical
communication’ to 1 s in order to have a faster response time when
section or PG state changes.
When periodical communication is set to just 1 s it can reduce
the typical battery lifetime by half.
Signalling PG tab:
The siren can indicate the activity of selected PG outputs with its beeps.
Slow beeping
- 1 per second (for the whole period when the PG
is active)
Rapid chirping
- 2 per second (for the whole period when the PG
is active)
1xOn/2xOff
- 1 chirp when the PG is activated, 2 chirps when the PG is
deactivated
20 seconds of beeping
– a long 20 sec beep when the PG is activated
Settings according to security grade 2
To set the siren to comply with security grade 2 use F-Link SW,
the ‘Parameters’ tab and the option ‘System profiles’ set to ‘EN50131-
1, gr.2’. Device will be configured according to required properties.
Sound priorities
The siren sound has the highest priority, the control chirps have a lower
priority and the PG output activity indication has the lowest priority
(PG1 has a higher priority than PG2 etc). A chirp with a higher priority
always terminates chirping with a lower priority.
External antenna use
To improve the communication quality between the control panel
and the outdoor siren you can connect an external antenna (AN-868). Plug
the antenna into the connector (15) on the PCB. Detection of a connected
antenna is performed only when the cover is open (active tamper).
If the siren during closing the cover detects the external antenna,
it is automatically used for radio communication. If the antenna is shorted
out or cut off, it automatically switches to the internal antenna and
a tamper alarm is sent. When the siren cover is closed with no external
antenna, the internal antenna is used for radio communication.
Battery replacement
The product checks the battery status automatically. When a battery
fault is triggered, the system informs its user (or service technician).
The siren remains fully functional, but we strongly recommend
to replace the battery is replaced within 2 weeks. Don´t charge
the battery at all. Use the BAT-100A type only. If two batteries are
used, always replace both batteries at once. The battery can be
changed in control panel service mode by a service technician.
When replacing is finished, test the siren’s functioning. Take the used
battery to an official collection point, don´t dispose in the general trash.
Technical specifications
The JA-163A RB parts (lithium battery, front cover and base) are
supplied individually. The reason is the free selection of a wide range
of a front covers and the transportation of lithium batteries.
Power
Lithium battery 3.6 V / 13 Ah type BAT-100A
(up to 2 batteries can be used)
Please note: battery is not included
Current consumption (nominal / maximal)
0.3 / 1000mA
Battery low voltage
2.8 V
Typical battery lifetime
approx. 5 years (for basic settings)
Communication frequency
868.1 MHz, JABLOTRON protocol
Communication range
approx. 300 m (open area)
Antenna
internal, external can be used, type AN-868
Activation lost integrity
acoustic tamper alarm (110 min)
Piezo electric siren
100 dB/m
Dimensions (cover included)
200 x 300 x 70 mm
Weight
434 g
Classification
security grade 2 / environmental class IV
- according to
EN 50131-1, EN 50131-4, EN 50131-5-3
- environment
general outdoor
- operational temperature range
-20 to +60°C
- power supply
type W
- operational humidity
75% (95% 30 days) RH, non-condensing
- certification body
Trezor Test s.r.o. (no. 3025)
Security grade
IP44
Also complies with
ETSI EN 300 220, EN 50130-4,
EN 55022, EN 60950-1
Can be operated to
ERC REC 70-03
JABLOTRON ALARMS a.s. hereby declares that the JA-163A RB
is in a compliance with the relevant Union harmonisation legislation:
Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU.
The original of the conformity assessment can be found
at www.jablotron.com - Section Downloads.
Note:
Although this product does not contain any harmful materials
we suggest you return the product to the dealer or directly
to the producer after use.
