JA-160PC (90) PIR motion BUS detector with a 90° verification camera
JA-160PC (90) PIR motion BUS detector with a 90° verification camera
2 / 3
MMQ53102
Instant:
During an alarm triggered by the detector, the camera can be
activated up to 3 times (then it will be auto-bypassed). Each activation,
depending on the detected movement, takes 2 photos maximum. Photos
are sent to the control panel (6 photos maximum).
Delayed:
The first activation (entrance delay) takes up to 2 photos
according to the detected movement and saves them into the internal
memory
(Send pre-alarm image
disabled
)
. When alarm is triggered, photos
are sent from the internal memory to the control panel. Then the behaviour
is the same as with an instant reaction (8 photos maximum).
Warning
: When the
Device autobypass / 3rd alarm
is enabled
(located in
Settings/Parameters
), then taking photos is blocked after
the 3rd alarm. During each alarm the detector can be triggered
up to three times. This way, the number of taken and transferred photos
can be tripled (18/24 photos). Applies to Instant/Delayed reactions.
Installation recommendations, cautions
Several JA-160PC (90)s can be installed in the system. However,
triggering several detectors at the same time will extend the transmission
time of photos to the control panel and to the external storage.
Complete transmission can take a few minutes.
Installation in the corner of a room requires more attention during
testing due to possible reflection of flash in the photographed scene
(especially in the dark).
In order to take a photo using a PG output, use the
F-Link
software
and set the
Impulse
parameter in the
PG outputs/Function
menu
to a time of at least 1 min. The PIR is limited to taking 1 requested
photo by PG status per minute.
The number of pre-alarm photos taken by a PG output is limited
to 40 photos/day/control panel. The photo counter is reset at 00:00 hrs.
Alarm photos and photos requested in MyJABLOTRON have no limitation.
When you start transferring the pictures to MyJABLOTRON
or external mass storage, it’s necessary to take into account the cost
of data transfer to be paid to your GSM provider.
Detection characteristics
PIR detector has a 90°/12 m coverage – see picture below.
The detection characteristics of the PIR part has no influence
on the camera part of the detector.
Warning:
-
The lens cannot be changed for other types.
-
The camera has a viewing angle of 90°, the camera flash has
a range of 3 m.
Saving and browsing the pictures
Every photo is taken twice: the first in low resolution (LQ = 320x240
pixels), the second with high resolution (HQ = 640x480 pixels).
All of the exposures are saved into the independent folders Foto_LQ
and Foto_HQ on the Micro SD card. When the card’s capacity is full, the
oldest photos will be replaced by new ones. Photos saved on the micro SD
card can be browsed in a photo browser on a PC.
Note:
Some antivirus software may write their own data on the Micro SD
card. The detector will automatically format the SD card marked this way.
SD card formatting erases all data which has been saved. For more
information about formatting see
Formatting the Micro SD card
.
Photos are sent to the control panel in LQ. You can browse through these
images in
F-Link
and
J-Link
software
event memory
by clicking
on an event called
New image
. Photos are displayed in LQ, if you click
on
Detail
you can get second-exposure pictures (HQ). Images can be
searched and browsed by a file manager or picture browser. In order
to display the photos this way it is necessary to start
F-Link (J-link)
software, be logged into the control panel as a service technician
or Administrator and then load the control panel memory.
Disc: Flexi_log /Foto.
Here are all the photos which have been sent to the
control panel (LQ) and photos which have been requested in
Detail
(HQ).
Picture transmission from the control
panel
It’s necessary to choose one of these options in order to send photos
to the user:
Transfer photos to MyJABLOTRON
When the SIM card supplied by a device manufacturer
(distributor)
is used and the customer uses MyJABLOTRON services, then the
customer has direct access to the photos from this service. Parameter
settings of the transfer of pictures are done during the panel
registration. All the photos are delivered and visible in MyJABLOTRON.
Every single photo can be requested in HQ resolution. There you can
also choose telephone numbers (for SMS) or e-mail addresses which
will receive a message when a new picture is taken. MyJABLOTRON
can request a new picture without PG output activation (see
Installation
recommendations, cautions).
MyJABLOTRON respects permissions of individual users concerning
photo verification accordingly to sections to which the users have
access (for example, a user from section 1 cannot browse through
photos from section 2)
Transferring pictures to external mass storage
If MyJABLOTRON is not available, photos can be transferred to external
mass storage
http://img.jablotron.com
. Communication parameters are
preset in the factory and are activated when the first PIR detector with
a camera is enrolled to the system and after agreeing with transfers.
When communication works properly the user must create an account
at
http://img.jablotron.com
by entering the login and password, and then
filling in the registration code of the control panel which will make
photos immediately available for browsing. The registration code
is on the control panel PCB or you can read it via
F-Link
software,
Communication
tab,
Registration code
field.
Reports of new photos stored in this mass storage can be sent
to an e-mail.
Note:
If there are more detectors in the premises, all photos will be
visible to all people with access to the created premises regardless
of the sections assigned to them.
Photos stored at
http://img.jablotron.com
are available only in LQ
quality. Photos in HQ quality cannot be requested.
In both cases sending reports straight from the control panel will
normally work. When the picture is saved at MyJABLOTRON
or http://img.jablotron.com, the control panel will send an SMS report
to all users depending on the settings in
F-Link
,
User reports
tab,
Alarm photo
settings. Sent SMSes include an http link to display the
photo. The photos can also be browsed on mobile phones with
a connection to the internet.
Warning:
-
This detector allows you to take photos by PG output reaction
or from MyJABLOTRON even when the system is unset.
The producer strictly warns the user that the detector has to
be used within the limits given by particular laws or norms,
especially laws about the protection of personal privacy.
-
The use of the detector is also subject to regulations
on the protection of personal data and the manufacturer
recommends that users be aware of the obligations applicable
to the operation of CCTV.
-
According to these regulations users have an obligation to ensure
the approval of persons in range of the detector during
the acquisition of video recordings or the obligation to indicate
the image capture area by information tables.
Formatting the Micro SD card
The detector is supplied with a formatted Micro SD card (12). The yellow
indication LED (11) is turned off in normal detector mode. Slow LED flashing
indicates that the card was removed while data was being written on it,
or it has been changed for another SD card. The detector will work
normally with a new SD card only if the detector performs a card formatting.
Formatting is started by pressing the tamper contact (14). The formatting
procedure is indicated by quick flashing of the yellow LED indicator (11).
During this process all photos on the SD card will be erased, however,
a back-up of the photos is in the event memory log, alternatively
in external storage.
Changing the batteries
The detector monitors its own batteries and when they are depleted,
it will inform you about this with a brief flash of the LED indicator when
the detector is triggered. This information is also delivered to the control
panel. We recommend changing the batteries within two weeks from the
moment the low battery indication starts. After replacing the batteries,
the detector sensor needs up to 3 minutes to stabilize (the red LED
indicator is lit up). The batteries should be replaced by a service
technician with the control panel in Service mode. Always replace both
Top view
Side view