JABLOTRON
ALARMS
a.s.
Pod
Skalkou
4567/33
46601
Jablonec
n.
Nisou
Czech
Republic
www
.jablotron.com
||
|
JA-156J Wireless multifunctional panic button
JA-156J Wireless multifunctional panic button
1 / 3
MOO51302
The device is a component of the
JABLOTRON
alarm system. It has
four defined types of utilization:
1. Panic alarm button activated by hand.
2. Panic alarm button activated by foot* or knee.
3. Detection of banknote removal or the removal of valuable
documents.
4. Verification of the presence of a person with a variable timer. All of
these options may be realized by utilizing the mounting platform,
which is equipped with a tamper detector.
Thanks to bi-directional communication, the device optically and
acoustically signals confirmation of a successful action. The device
utilizes wireless Jablotron communication protocol and is powered by
two AAA batteries. The device takes up one position in the system.
The device should be installed by a trained technician with a valid
certificate issued by an authorized distributor.
This product is compatible only with the JA-103K, JA-107K and
subsequent systems.
Fig. 1: Panic button in its mounting platform: 1. Hinges,
2. Button A, 3. Switch B, 4. Backplate fixing screw, 5. Mounting platform
latches, 6. Replaceable banknote or document clip, 7. LED light guide.
Modes of operation of the wireless
multifunctional panic button
The wireless multifunctional panic button is a device intended to
enable the user to activate a panic alarm should the user find
themselves in a situation requiring it. The device has multiple modes of
activation, which must be configured via
F-Link
once the device has
been enrolled onto the system.
1.
Panic alarm activation by pressing the A button
(By hand, foot*
or knee)
Activation of the panic alarm button is, depending on the orientation
of the device in the mounting platform achievable either by directly
pressing the red button or, alternatively by pressing anywhere on its
surface. To activate the device by pressing on its surface, the button
must be placed in the mounting platform facing the plastic
protrusion. The protrusion-facing device is especially suitable for
activation by knee or foot*, should the device be mounted under the
user’s desk. Should it be deemed suitable, activation of the device
may be mechanically verified by applying an indicative self-adhesive
seal onto the red button (1pc. of self-adhesive seal is included in the
packaging).
*Important:
Not meant for full body weight activation.
2.
Banknote removal detection via switch B.
With the utilization of this function, it is necessary to replace the
default light guide as shown on Fig. 5, with a light guide equipped
with a clip (6) on Fig. 1, which is included in the packaging.
Banknote removal detection may be utilized to protect contracts or
any other valued documents. in a safe or a security box.
To utilize this mode of operation, place a banknote into the clip
specialized for this purpose (6). The device may be fixed in this
configuration to the bottom of a cash register in a store, a gas
station, etc.
Removing the banknote from the device will result in an immediate
activation of switch B.
3.
Verification of the presence of a person via repeated button A
activation.
Device activation occurs if the user does not trigger the device
within a preset timeframe which may be set from 30 minutes to 12
hours (by 30 minutes steps). It is also possible to set a warning
period that causes activation once the timeframe expires, where the
user is be notified acoustically and visually for a period of 1 to 120
seconds in order to remind them to activate the button. In case that
an activation does not occur, the system will receive a pre-defined
report. It must be noted that the timer is reset every time the button
is pressed and when the system is put into service mode.
Important:
This function has been designed with continuous (24/7)
operation in mind. If it is required by user specification, the function
may be blocked
via a PG output with an on/off function, which may
for example be controlled by a keypad segment with the
authorization of the employee or controlled by calendar events.
Fig. 2: Panic button equipped with a bank note holder
Installation
We recommend installing the panic alarm button onto the mounting
platform (Fig 3.). The mounting platform allows for installation onto
various types of surfaces and allows for the detection of tampering
should the device be removed from the mounting platform. The device
may be used without the mounting platform, however due to the fact that
the tamper device is not present it is necessary to disable the device’s
tamper sensor via F-Link. It must be noted that utilizing the device
without its mounting platform results in non-conformity to Security Grade
II classification.
Fig. 3: Mounting platform: 1. Hinges, 2. Fixing screw holes, 3. Latches,
4. Button activation plastic protrusion, 5. Sabotage magnet segment
(sabotage sensor)
Mounting platform installation
instructions
1. Remove the panic button from its mounting platform by applying
small force to the sides of the hinges, (1, 3) see Fig.3, thus prying
them apart. This action is best performed with the use of a flat tool.
2. Fix the mounting platform to the desired location with the use of four
screws. (2).
3. Remove the device’s backplate, this action may be performed by
prying it away with the use of a flat-head screwdriver as shown in
Fig.4.
4. Basic procedure: Enroll the device onto a JABLOTRON system,
Follow the instructions stated in the control panel installation
manual. Basic procedure:
a. Select a position in the
Devices
tab, in
F-Link
and click the
Enroll
prompt in order initiate enrollment mode.
b. Inserting the batteries (both batteries must be inserted into the
device) will result in the transmission of an enrollment signal and
the device will be enrolled onto the selected system position.
c. Property settings may be adjusted within
F-Link
’s
Devices
tab.
