Jabiru j160 Скачать руководство пользователя

Страница: 254 / 298

Aircraft Technical Manual

Jabiru Aircraft

Pty Ltd

J120, J160, J170, J200/J400, J230/J430, J250/J450 Variants

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

Dated: 29th October 2014

Issued By: AS

Page: 254 of 298

11.5.8 Trouble Shooting

– Airspeed Indicator

Table 11-2

– Trouble Shooting – Airspeed Indicator

Trouble

Probable Cause

Remedy

Hand fails to response

Pitot pressure connection not

properly connected to pressure

line from pitot tube

Test line and connections for

leaks. Repair or replace

damaged line, tighten

connections

Pitot or static lines clogged

Check line for obstructions. Blow

out lines.

Incorrect indication or

hand oscillates

Leak in pitot or static lines

Test lines and connections for

leaks. Repair or replace

damaged lines, tighten

connections.

Defective mechanism or leaking

diaphragm

Substitute known-good indicator

and check reading. Replace

instrument.

Hand vibrates

Excessive vibration

Check panel shock mounts.

Replace defective shock mounts

Excessive tubing vibration

Check clamps and line

connections for security. Tighten

clamps and connections, replace

tubing with flexible hose.

11.5.9 Trouble Shooting

– Altimeter

Table 11-3

– Trouble Shooting – Altimeter

Trouble

Probable Cause

Remedy

Instrument fails to

operate

Static line plugged

Check line for obstructions. Blow

out lines

Defective mechanism

Substitute known-good altimeter

and check reading. Replace

instrument

Incorrect indication

Hands not carefully set

Reset hands with knob

Leaking diaphragm

Substitute known-good altimeter

and check reading. Replace

instrument.

Pointers out calibration

Compare reading with known-

good altimeter. Replace

instrument

Hand oscillates

Static pressure irregular

Check lines for obstruction or
leaks. Blow out lines, tighten

connections.

Leak in airspeed or vertical

speed indicator installations

Check other instruments and

system plumbing for leaks. Blow

out lines, tighten connections

Содержание j160











































































































































































































































































































Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды

Jabiru j160, Техническое руководство

Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды