Jabiru j160 Скачать руководство пользователя

Страница: 173 / 298

Aircraft Technical Manual

Jabiru Aircraft

Pty Ltd

J120, J160, J170, J200/J400, J230/J430, J250/J450 Variants

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

Dated: 29th October 2014

Issued By: AS

Page: 173 of 298

6.64 Control Column (all J-Series)

6.64.1 Description



The same control panel is used for the elevator as for the ailerons. Drawings of the system are given

in Section 0.



A central shaft is located between the crew seats. The control column is mounted at the fwd end of

this shaft via a pivot.

6.64.2 Removal And Installation



Refer to the details given in Section 0.

6.65 Elevator (all J-Series)

6.65.1 Description



The elevator comprises a Rigid Cellular Polystyrene core moulded and bonded to a composite skin

and embodying a composite control horn at the centre. An elevator trim system is attached

– refer to

Section 6.68.



Note that some models (J170-C, J230, J250 families etc) use a wider-span horizontal tail and

elevator than the J160. This elevator is driven by the same control assembly as the J160.

6.65.2 Removal & Installation

Required Tools:

Screwdrivers
Spanners / Socket Wrench

Parts and Material:

N/A

Type of Maintenance:

Line Maintenance

Level of Certification:

L1, L2 or LAME (Owner, A&P or LSA Repairman / Maintenance)

Return to Service:

L1, L2 or LAME (Owner, A&P or LSA Repairman / Maintenance)

Remove ventral fin from under tail to expose control cables etc.

Unbolt cable from control horn.

Unbolt trim linkage from control horn.

Loosen screws in hinge pin retainers and lift hinge pin retainers from hinge pins. It is not
necessary to remove these parts.

Remove hinge pins.

Remove Elevator.

Reverse the preceding steps for installation.

6.65.3 Elevator Balancing (J160, J170)



The J160/J170 Elevator is balanced during construction. A standard weight of 750 grams of lead is

placed in each control horn to balance the elevator. In service there should be no reason to
rebalance the elevator.



For the J160-C, balance may be checked with the control fitted to the aircraft & the control & trim

removed. Measure the force at the trailing edge required to keep the elevator level. Weight & hinge
moment values are given below:
-

Weight

4600g

+/- 100g

Hinge Moment

259000g.mm

+/- 4000g.mm

Содержание j160











































































































































































































































































































Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды

Jabiru j160, Техническое руководство

Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды