Jabiru j160 Скачать руководство пользователя

Страница: 178 / 298

Aircraft Technical Manual

Jabiru Aircraft

Pty Ltd

J120, J160, J170, J200/J400, J230/J430, J250/J450 Variants

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

Dated: 29th October 2014

Issued By: AS

Page: 178 of 298

6.68 Elevator TRIM

– CONTROL LEVER ASSY (all J-Series)

6.68.1 Description



The control lever for the elevator trim is mounted on the centre console.



The assembly includes friction plates so that the lever does not move once in position.

6.68.2 Trim Control Lever Removal

Required Tools:

Fine nosed Pliers
Spanners / Socket Wrench
Screwdrivers
Drill (if required)

Parts and Material:

New rivets (for reinstallation)
New Cotter pin (for reinstallation)

Type of Maintenance:

Line Maintenance

Level of Certification:

L1, L2 or LAME (Owner, A&P or LSA Repairman / Maintenance)

Return to Service:

L1, L2 or LAME (Owner, A&P or LSA Repairman / Maintenance)



For a type 1 assembly:

Remove the cotter pin and lock nut from the lever pivot.

Remove the locking bolt from the front of the friction plate.

Remove the lever from the pivot shaft.

Remove the machine screw attaching the control cable to the lever

Remove the assembly from the centre console.



For a type 2 assembly:

Remove the cotter pin and lock nut from the lever pivot.

Remove the lever from the pivot shaft.

Remove the machine screw attaching the control cable to the lever

If required, drill the TLR rivets to remove the housing from the centre console.



For a type 2 assembly:

Remove the cotter pin and lock nut from the pivot shaft.

Remove the levers from the pivot shaft

Remove the machine screw attaching the control cable to the lever

If necessary, drill the rivets to allow removal of the pivot housing. Note that the two end pieces of
the housing connect to the central spacer with a thread and will need to be un-screwed for
disassembly.

6.68.3 Inspection & Repair



Inspect the friction plates for excess wear, galling or other damage.



After installation carry out the functional tests and inspections noted below.

6.68.4 Installation



Reverse the removal procedure above for installation.



Adjust the tension of the pivot bolt to give the required friction force.



Use a new cotter pin.

WARNING

All spherical rod end bearings must be fitted with a large washer on the outside of the through-

bolt to prevent the bearing case and cable releasing in the event of a bearing failure.

Содержание j160











































































































































































































































































































Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды

Jabiru j160, Техническое руководство

Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды