Jabiru j160 Скачать руководство пользователя

Страница: 112 / 298

Aircraft Technical Manual

Jabiru Aircraft

Pty Ltd

J120, J160, J170, J200/J400, J230/J430, J250/J450 Variants

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

Dated: 29th October 2014

Issued By: AS

Page: 112 of 298

6.30 Main Wheels (all J-Series)

6.30.1 Description



The main wheels consist of an inner rim half

– also containing the bearings and brake disc mounting

and an outer half.



Main wheel rims are cast Aluminium.



Figure 68 shows a typical installation. While details and part numbers vary from model to model the

general arrangement shown applies to all aircraft.

6.30.2 Main Wheel Removal

Required Tools:

Wing Stand - Construct from DAR pine, wood screws and a foam or thick
carpet padding.
Jack
Spanners / Socket wrench
Bead breaker

Parts and Material:

N/A

Type of Maintenance:

Line Maintenance

Level of Certification:

L1, L2 or LAME (Owner, A&P or LSA Repairman / Maintenance)

Return to Service:

L1, L2 or LAME (Owner, A&P or LSA Repairman / Maintenance)

Jack aircraft as outlined in Section 6.27 above.

Remove the upper leg/fuselage fairing and the wheel spat (if equipped) as detailed above.

Remove outboard brake pad plates.

Remove lock bolt/nut through the axle extension.

Remove axle extension.

Pull wheel from axle.

6.30.3 Main Wheel Disassembly

Deflate tyre and break tyre beads loose from tyre rims. A bead-breaker or similar may be
required for this task.

WARNING

Injury can result from attempting to separate wheel halves with the tyre inflated. Avoid damaging

wheel flanges when breaking beads loose as a scratch, nick or gouge may cause wheel failure.

Remove through-bolts/nuts and separate wheel halves, removing tyre, tube and wheel hub.

Remove brake disc.

Remove bearings from hub.

Note:

The bearings are “press-fit” in the wheel hub and should not be removed unless a new part

is to be installed.

6.30.4 Main Wheel Inspection, Assembly and Repair

Required Tools:

Solvent
Course grit sand paper
Spanners / socket wrench
Torque wrench

Parts and Material:

Replacement wheel halves (if required)
Replacement Brake discs (if required)
Replacement Wheel bearings (if required)
Automotive wheel rim lubricant

Type of Maintenance:

Heavy Maintenance

Level of Certification:

L2 or LAME (A&P or LSA Repairman / Maintenance)

Return to Service:

L2 or LAME (A&P or LSA Repairman / Maintenance)

Содержание j160











































































































































































































































































































Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды

Jabiru j160, Техническое руководство

Результаты поиска

Содержание j160

Отзывы:

Похожие инструкции для j160

Бренды по названию

Популярные бренды