Jabiru 2200 Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 201

background image

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

1

2

3

4

5

6 7

Dated : 28/10/2014

Issued By: AS

Page: 96 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

Figure 113

– Fitting New Float Needle Seat



The float bowl needle seat must be checked. 3300 engines use a 2.4mm diameter, specially shaped

orifice in this part while the 2200 engine uses 2.0mm (though the 2200 can also use a 2.4mm seat if
required). Figure 30 shows the tools needed to change the seat which is located in the carburettor
body above the float needle. As noted at Figure 30, if the seat is to be changed a tap is used to remove
the old part and a special nylon drift used to install the new.

Figure 114

– Carburettor Jets & Diaphragm



During re-assembly ensure that the atomiser, needle jet, jet carrier, washer and main jet are installed in

the correct orientation and correct order as shown in Figure 114 (left). Also ensure that the tag on the
diaphragm is aligned and fitted correctly to the socket in the carburettor body as shown in Figure 114
(right)



Check the idle mixture screw. Screw fully in then screw it out 1 turn for 2200 and 3300 engines. The

idle screw is shown in Figure 112.



The float level must be set at 11-13mm down from the lip of the bowl. Adjust the brass tang of the float

as required. An alternate setting method is to turn the electric fuel pump on and lift the floats, noting at
what float height the flow cuts off.



Carefully check the condition of the rubber coupling between the carburettor and the engine.

Particularly on installations where a “pod” filter is used this coupling can crack – and the cracks can be
hard to spot.



Set the throttle butterfly idle stop so that the butterfly is just cracked. This setting will then need to be

confirmed during the engine test run.

5.15.2 Fuel Pump

5.15.2.1 Inspection & Repair



Top End Overhaul:

check fuel pump diaphragms and gaskets, replace as required.

Atomiser

Needle

Jet

Jet

Carrier

Main Jet

Washer

Using thread tap to remove old seat

Fitting new seat using Nylon tool

«
...
94
95
96
97
98
...
»

Содержание 2200










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2200

Бренд: BAFANG Страницы: 4

Бренд: Grizzly Страницы: 2

Бренд: Tecumseh Страницы: 94

Sonesse Ultra 50 DC RS485

Бренд: SOMFY Страницы: 16

Бренд: Oxygen Страницы: 6

Бренд: King Canada Страницы: 8

Бренд: O.S. engine Страницы: 4

Бренд: Daewoo Страницы: 188

Бренд: Harmonic Drive Страницы: 48

24 v High Performance Synchronous Motor

Бренд: Rega Страницы: 1

Бренд: Marcato Страницы: 42

Бренд: Habasit Страницы: 60

Бренд: SPE Страницы: 7

Бренд: TEM Страницы: 19

75-200 V DC Series

Бренд: TEM Страницы: 38

Бренд: TEM Страницы: 42

Бренд: Greyhound Страницы: 19

Бренд: MULTIPLEX modell Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды