Jabiru 2200 Скачать руководство пользователя

Страница: 90 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 90 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

Figure 105

– Starter Motor Overhauling

5.13.4 Engine Mount Plate

5.13.4.1 Mandatory Updates



As noted above, engine mount plates are specific to the flywheel ring gear used

– there are 99 and 101

tooth versions of the plate to suit the different gears. Parts must be matched on assembly.



Note that the 2200 mount plate is shorter (vertically) than the 3300 plate.

5.13.4.2 Inspection And Repair

Figure 106

– Checking Engine Mount Plate Trueness



Check to ensure the plate being inspected is suitable for use on the engine

– matching the ring gear

and the engine model.



Using a straight edge, carefully check the plate in both directions for trueness. Often an engine which

has been in an accident or had a severe propeller strike will be bent. Figure 106 refers

Содержание 2200










































































































































































































Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды

Jabiru 2200, Руководство по капитальному ремонту

Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды