Jabiru 2200 Скачать руководство пользователя страница 89

Страница: 89 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 89 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

Figure 103

– Starter Motor Old & New

5.13.3.2 Cleaning



Clean and wash all parts in solvent except the motor. Clean the motor by wiping with a clean rag to

remove dust and metal particles. Clean the commutator with a soft brush and a fast drying solvent
(Figure 105, left).

5.13.3.3 Inspection And Repair



Check commutator for wear, if you are not experienced in this field then seek a suitable qualified person

to check the commutator for serviceability.



Check brushes for wear, if you are not experienced in this field then seek a suitable qualified person to

check the brushes for serviceability, replace if they are less than 10 mm long.



Check bendix gear for chipped or missing teeth, and that the clutch slides freely on the shaft, replace if

necessary.



Check the ball bearings on the motor rotor for serviceability, replace if necessary (Figure 105, right),

using a suitable puller to remove the old part.



Check the bushes at each end of the clutch and bendix gear for wear and replace as required, lubricate

the bushes with grease.

Figure 104

– Typical Disassembled Starter Motor

Содержание 2200










































































































































































































Результаты поиска

Содержание 2200

Отзывы:

Jabiru 2200, Руководство по капитальному ремонту, Страница: 89 / 201

Результаты поиска

Содержание 2200

Отзывы: