Jabiru 2200 Скачать руководство пользователя

Страница: 77 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 77 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

5.11.4 Valve guides

Figure 88

– Valve Guides



Top End Overhaul:

start by holding each valve partly open and feeling for wear in the guide as shown

at right

– there should only be a small amount of up and down (see direction arrow in Figure 88)

movement in the head of the valve.



Check each valve in this manner.



Use a micrometer to measure the valve stems and the valve guide bores and calculate the clearance: it

must be within the limits set in Table 12. If the clearance is greater than this then new valve guides
must be purchased and fitted.



Note that the values given above are maximums

– there is no point returning a cylinder head to service

if it has valve guides already worn close to the maximum allowable

– before the engine has completed

its next cycle the guides will be unserviceable. Refer also to Section 12 for details.



It is unusual for guides to need to be replaced after 1 cycle however it can happen.

Figure 89

– Measure Guide Wear (Telescopic Gauge Left & Middle, Go-No-Go Gauge Right)

Check the valve for movement

Содержание 2200










































































































































































































Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды

Jabiru 2200, Руководство по капитальному ремонту

Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды