Jabiru 2200 Скачать руководство пользователя

Страница: 70 / 201

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

6 7

Dated : 28/10/2014

Issued By: AS

Page: 70 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

5.10.4.2 Cleaning



Wash the pump rotors and housing thoroughly with kerosene and dry.



Coat the pump rotors with engine oil or other corrosion preventative.

5.10.4.3 Inspection



Inspect visually for any signs of wear or damage to the rotor surfaces.



Visually inspect the woodruff key which drives the pump. It is normal for there to be some light marking

on this part, however significantly marked keys must be replaced.



Measure the clearances between the parts and ensure they are within the limits given in Table 12.



Note that oil pump gears must be replaced as a set.



Replace any components that fail to meet these requirements.



Note that the inner and outer rotors each have a machined alignment marking as shown arrowed in

Figure 80. These alignment markings must both face up when the rotors are in the housing.



Note also that the alignment markings will move in relation to each other as the inner rotor rotates in

relation to the outer rotor.

Figure 80

– Inspecting Oil Pump

5.10.5 Oil Pressure Relief Valve

5.10.5.1 Mandatory updates

Figure 81

– Oil Pressure Relief Valve

Содержание 2200










































































































































































































Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды

Jabiru 2200, Руководство по капитальному ремонту

Результаты поиска

Содержание 2200

Отзывы:

Похожие инструкции для 2200

Бренды по названию

Популярные бренды