Jabiru 2200 Скачать руководство пользователя | Manualshive

Страница: 40 / 201

background image

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

1

2

3

4

5

6 7

Dated : 28/10/2014

Issued By: AS

Page: 40 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

4 Disassembly Procedure



As each part is removed from the engine it should be set aside for later evaluation

– in our factory

engine workshop we use disposable plastic containers to keep all of the smaller components (cap
screws, bolts, nuts, washers, etc) separate during disassembly.

4.1 Preliminary Cleaning



Inspect engines carefully before cleaning. The patterns of dirt, oil etc can indicate damage or wear and

provide valuable information of which tasks should be added to the overhaul or inspection process.



The engine must be cleaned externally before it is removed from the aircraft. A stiff-bristled brush,

solvent (de-greaser), water and some compressed air will usually be adequate for this task.

4.2 Remove The Engine From The Aircraft



Remove the cowlings and the spinner. Remove the propeller. Disconnect both cables from the battery

and remove the battery from the aircraft. Disconnect the earth cable and free the starter motor power
cable from the wiring loom.



Remove the muffler and then remove the oil drain plug and drain the oil from the engine. Remove the

ram air ducts. Disconnect all engine control cabling and disconnect the air intake duct from the
carburettor. Remove the oil filter, the oil filter adapter and oil cooler.



Disconnect and remove all engine wiring: the signal wiring from the oil pressure and temperature

senders and fuel pressure sender (if fitted), the low-tension ignition wiring and the alternator wiring.
Remove the oil pump from the front of the engine and undo the cap screws that hold the front oil seal
around the crankshaft.



Remove the engine from the airframe and place it onto the engine stand, holding it in place with 3 bolts

through the propeller flange.

4.3 Engine Stand



We recommend that an engine stand be used to hold the engine vertically during all workshop

procedures.



In our engine workshop we use a spare propeller flange bolted to the workbench. The propeller flange

on the engine is then bolted to that flange so that the engine is held in an upright position as shown in
Figure 44.



You may find it convenient to simply bolt the propeller flange of the engine directly to the workbench

using 3 suitable bolts.



Note that for a top end overhaul the engine can remain in the aircraft, although the use of an engine

stand may be more convenient and is usually faster.

Figure 44

– Engine Stand

«
...
38
39
40
41
42
...
»

Содержание 2200










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2200

Бренд: O.S. engine Страницы: 32

950-1020 MOTOR KIT 8504048 REV 2 1297

Бренд: TJERNLUND Страницы: 2

Бренд: Nanni Страницы: 24

Бренд: Ridder Страницы: 16

Бренд: CHERUBINI Страницы: 24

MaxxForce 3.2H Euro V

Бренд: Navistar Страницы: 116

Бренд: TecumsehPower Страницы: 24

Бренд: Tecumseh Страницы: 20

Бренд: Tecumseh Страницы: 8

Бренд: SunStar Страницы: 86

Бренд: Caple Страницы: 16

Бренд: DUROMAX Страницы: 70

Бренд: ARO Страницы: 2

Бренд: ARO Страницы: 8

Бренд: DLE Страницы: 4

Бренд: DLE Страницы: 4

Бренд: Ingersoll-Rand Страницы: 42

Бренд: Black Bruin Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды