Jabiru 2200 Скачать руководство пользователя | Manualshive

Страница: 104 / 201

background image

Engine Overhaul Manual

Jabiru Aircraft

Pty Ltd

Jabiru 2200 & 3300 Aircraft Engines

This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.

ISSUE

1

2

3

4

5

6 7

Dated : 28/10/2014

Issued By: AS

Page: 104 of 201

L:\files\Manuals_For_Products\Engine_Manuals\Overhaul_Manual\JEM0001-7_Overhaul_Manual_DRAFT_(29_10_14).docx

7.2 Subassembly B

– Crankcase and camshaft

7.2.1 Crankcase

Figure 121

– Crankcase Assembly Preparation



Lubricate and fit the O rings to the bottom main bearing stud holes (arrowed in Figure 121 - left) and

then fit the front and rear crankcase studs using Loctite 620 Retainer: clean and prime the threads first
using Loctite 7471 cure accelerator. Use a collet type stud tool to screw the 2 short front crankcase
studs to a free length of 52mm and the 2 long front and the 2 rear crankcase studs to a free length of
95mm as shown in Figure 121. Note: Later longer studs are positioned 54mm and 97mm free length
above the crankcase join.



Fit the hollow dowels to one crankcase half in the positions arrowed above. It is vital that poorly fitted

dowels are not used at the crankcase join

– if the dowels can be pushed in by hand then they are too

loose.  The correct fit it a light “tap” fit using a soft hammer.  Oversize dowels are available to ensure a
snug fit. These are identified by “dots” machined into them as shown in Figure 122 – the standard size
has  no  dots  then  the  size  increases  progressively  up  to  the  3-dot  dowel  which  is  the  largest  size
available.    Experience  in  Australia  has  shown  that  1-dot  dowels  are  suitable  for  most  overhauled
engines with 2-dot and 3-dot parts being used very occasionally.



The overhauler may opt to fit somewhat loose-fitting dowels for temporary assembly of the engine to

measure bearing sizes. This simplifies sebsequent disassembly. Where such parts are used they must
be clearly marked so that they are not fitted to an engine during final assembly by mistake.

WARNING

Ensure correct size dowels are used for final assembly.

Figure 122

– Crankcase Dowels

Short front crankcase studs: 52mm min

Long front and rear crankcase studs: 95mm min

«
...
102
103
104
105
106
...
»

Содержание 2200










































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2200

Бренд: Hacker Страницы: 8

Бренд: Westerbeke Страницы: 86

Бренд: DAF Страницы: 87

Бренд: Kohler Страницы: 109

ALCYO ACCU-TRK-AT

Бренд: Oben Страницы: 28

1550 STERNDRIVE

Бренд: Mercury Racing Страницы: 75

Бренд: Perkins Страницы: 27

Бренд: Wisconsin Motors Страницы: 46

MAX-15CV-R Series

Бренд: O.S. engine Страницы: 34

Бренд: O.S. engine Страницы: 34

Бренд: O.S. engine Страницы: 40

Бренд: Lycoming Страницы: 568

SKALAR SC Series

Бренд: Hacker Страницы: 2

Бренд: CAME Страницы: 64

Бренд: ST. SpA Страницы: 20

Бренд: ST. SpA Страницы: 22

Бренд: Honda Страницы: 31

Бренд: WilTec Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды