J.A. Woollam M-2000 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 178

background image

M-2000® Hardware Manual

©2023 J.A. Woollam Co.

147

9.

Iterate these steps until no further improvement is achieved. The beam
should be round and uniform, along with the maximum signal
achievement.

10.

Verify the System Alignment as described in Chapter 4 of this manual.

Arc Lamp Disposal

Warning: Compact arc lamps contain highly pressurized gas, and present an

explosion hazard even when cold. Wear face protection, such as a
full-face shield, gloves and a long sleeve shirt whenever handling
lamps.

1.

Wrap lamp in 10 to 15 layers of paper towels.

2.

Insert wrapped lamp in a plastic bag and seal the bag.

3.

Wearing personal protective equipment, smash center part of the glass
bulb with a hammer.

4.

With no pressure, the lamp (wrapped and still in the sealed bag) is safe to
dispose.

Mirror Replacement

The reflective mirror can be contaminated over time which could cause loss in
signal intensity. This can be monitored by the Ellipsometer and/or visually
checked when the lamp is changed. The mirror is low cost and easy to replace if
it is suspected to be contaminated.

MIRROR

JAW P/N

DESCRIPTION

TYPICAL
LIFETIME

JAW CUSTOM

10408001

CUSTOM PL/CC

3000 hours

Table 10-3. Mirror Part Description.

1.

Remove the cover plate from the back of the Lamp Housing.

2.

Loosen the screw which mounts the retainer clip.  Rotate the retainer clip
so that it is no longer contacting the mirror.  The mirror is loose fit such
that gravity will allow this to “fall out.”  An adhesive surface or optical
vacuum wand can be used to pull it out.

3.

Install the new mirror (reflective side down) and rotate the retainer clip
such that it is centered on the back of the mirror. Tighten the retainer
clip screw to hold the mirror in place. Check that it is applying enough
pressure to hold the mirror stable.

«
...
145
146
147
148
149
...
»

Содержание M-2000



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для M-2000

Бренд: Hammond Страницы: 754

Бренд: Kawai Страницы: 2

Бренд: Datron Страницы: 197

Бренд: DAE Страницы: 28

Бренд: Oakton Страницы: 69

Бренд: KROHNE Страницы: 34

Бренд: QuantAsylum Страницы: 70

Бренд: Valcom Страницы: 1

Veeder-Root 7990 Series

Бренд: Danaher Страницы: 8

Бренд: Technoline Страницы: 1

Бренд: janitza Страницы: 128

Бренд: H-Star Страницы: 36

Бренд: Analog Arts Страницы: 8

Heavy Duty 2270-20

Бренд: Milwaukee Страницы: 33

Бренд: Leica Страницы: 2

DIGIMET E30 Preset

Бренд: MATO Страницы: 20

Бренд: Alfa Laval Страницы: 18

Бренд: Omega Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды