background image

September 13, 2016

 

 

 
Wood should not be stocked within the minimums clearances or in the necessary space 
for loading and ash disposal. Always use dried wood.  Do  not  burn green or wet  wood. 
Do not use construction debris such as pieces of 2x4, plywood. 
 
If the appliance starts to turn red, it is too charged. Do not add fuel. Close the door and 
the  wall  thermostat  immediately  in  order  to  close  all  the  air  until  everything  becomes 
normal again. 

Do not load the appliance over the firebricks height.

 

 
Ash  must  be  removed  frequently,  put  in  a  steel  container  provided  with  a  tight  lid  and 
placed outside at once. You must never place other waste in this container.

 

 
Under  certain  circumstances,  it  needs  additional  air  supply  for  combustion.  Leave  a 
window or a door slightly open to balance the pressure in the house, especially if: 
 

  A fan already blows air towards outside (kitchen, bathroom). 

  You want  to avoid  a repression of smoke when lighting the appliance and when 

reloading the wood. 

 
It is recommended to have a smoke detector near the appliance. 

 
You should contact your municipal or provincial fire department for the procedure 
to follow in case of a chimney fire. Prepare an emergency plan. 

 

In case of a chimney fire: 

 

  Close the door and the air intakes hermetically. 

  Water the combustible material adjacent to the chimney. 

  Ring the alarm, evacuate the house if necessary and call the firemen. 

  Never touch the pipes until the fire is completely extinct. 

  Do not use the chimney until it has been inspected or repaired. 

 
Keep  all  the  doors  closed  while  the  appliance  is  in  function.  Frequently  verify  the 
ceramics cords; they must always be in good condition. 
 
The chimney pipe should not be placed near water, gas or oil pipes, electric wire, other 
types of ducts or combustible materials in the roofs, the attics, the walls or the floors. If 
you  have  to  make  it  pass  through  a  wall  or  a  part  of  combustible  construction,  do  not 
forget that the installation must be in accordance with the CAN/CSA-B365. Use at least 
12 feet of 6 inch diameter vertical chimney. 
 

NOTE:  FOLLOW  THESE  INSTRUCTIONS  IN  ORDER  TO  AVOID  FIRE  HAZARDS, 

WOUNDS AND PROPERTY DAMAGES.

 

Содержание GRIZZLY FURNACE



























Отзывы: