IXXAT CME/PN Скачать руководство пользователя страница 13

Appendix 

 

4  Appendix 

4.1 

Support  

For more information on our products, FAQ lists and installation tips, please 
refer to the support area on our homepage (http://www.ixxat.de). There you 
will also find information on current product versions and available updates. 

4.2 

Returning hardware 

If it is necessary to return hardware to us, please download the relevant RMA 
form from our homepage and follow the instructions on this form.  

4.3 

FCC Compliance 

Declaration of conformity 
This device complies with Part 15 of the FCC Rules. Operation is subject to 
the following two conditions: 

 

 

This device may not cause harmful interference, and 

 

this device must accept any interference received, including interference 

that may cause undesired operation 

 

Class A digital device – Instructions 
Note: This equipment has been tested and found to comply with the limits for a 
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference when 
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential ar-
ea is likely to cause harmful interference in which case the user will be re-
quired to correct the interference at his own expense. 

4.4 

Disposing of old equipment 

This product is covered by ElektoG (WEEE) and has to be disposed according 
to ElektoG (WEEE) separately. Products of IXXAT, which are covered by 
ElektoG, are exclusively for commercial use and marked with the symbol of 
the crossed-out garbage can. 
According to the B2B regulations, the disposal in accordance with § 10 para. 2 
clause 3 Electrical and Electronic Equipment act in the version of 16.03.2005 
is regulated separately in the General Terms and Conditions and its supple-
ments  of IXXAT. The terms and conditions, its supplements and other infor-
mation on disposal of old equipment can be downloaded at www.ixxat.de. 

Copyright IXXAT Automation GmbH 

13

 

IXXAT CME/PN-Manual, Version 1.0 

 

Содержание CME/PN

















Отзывы: