iWave i.MX6 Qseven PMIC SOM Скачать руководство пользователя страница 43

Страница: 43 / 82

REL 1.2

Page 43 of 82

i.MX6 Qseven PMIC SOM Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.8.1

Parallel LCD Display Interface

i.MX6 Qseven PMIC SOM supports one Parallel RGB display interface and MIPI DSI interface on Expansion

connector1 along with two LVDS display & one HDMI display on Qseven Edge connector. i.MX6 CPU’s IPU is used for

parallel LCD display interface which supports upto 24bit data bus (8bits/colour). i.MX6 CPU’s LCD can support data

rate up to 220 Mpixels/sec (e.g. WUXGA+@ 60Hz).

For more details, refer Expansion connector1 pins 2,4,6 & 20 to 47 on

Table 6

and Expansion connector2 pins

41,43,44 & 45 on

Table 7.

Note: i.MX6 Duallite and i.MX6 Solo CPU supports only one IPU and so at any time only two display interfaces

(including LVDS, HDMI & MIPI DSI) can be supported.

2.8.2

MIPI DSI Interface

i.MX6 Qseven PMIC SOM supports dual lane MIPI DSI interface (excluding clock lane) @ 1Gbps on Expansion

connector1. i.MX6 CPU’s IPU with MIPI DSI Host controller & MIPI D-PHY is used for MIPI DSI interface. It is

compliant with MIPI Alliance Specification for Display Serial Interface (DSI), Version 1.01.00 - 21 February 2008 with

DPI-2 & DBI-2 support. It supports programmable display resolutions from 160x120(QQVGA) to 1280x720(XVGA). It

supports different Video Mode Pixel Formats, 16 bpp(RGB565), 18 bpp(RGB666) packed, 18 bpp(RGB666) loosely &

24 bpp(RGB888).

For more details, refer Expansion connector1 pins 46,48,55,56,57 & 58 on

Table 6.

Note: i.MX6 Duallite and i.MX6 Solo CPU supports only one IPU and so at any time only two display interfaces

(including LVDS, HDMI & MIPI DSI) can be supported.

2.8.3

Parallel Camera Interface1

i.MX6 Qseven PMIC SOM supports one camera interface on Expansion connector1 along with one more camera

interface & MIPI CSI interface on Expansion connector2. i.MX6 QuadPlus/Quad/DualPlus/Dual CPU has two IPU block

and each IPU has two input ports CSI0 and CSI1 which can receive data concurrently and independently. At any given

time, an IPU input port may receive data either from a parallel external port or from the MIPI/CSI-2 receiver.

i.MX6 IPU’s CSI0 parallel port is used for camera1 interface which provides direct connectivity to most relevant

image sensors and to TV decoders. The sensor is the master of the pixel clock (PIXCLK) & synchronization signals

where synchronization signals can be received using dedicated control signals method (HSYNC & VSYNC) or controls

embedded in data stream method (BT.656 protocol). i.MX6 Qseven PMIC SOM supports 8bit camera interface.

For more details, refer Expansion connector1 pins 64 to 76 on

Table 6.

Note: i.MX6 Duallite and i.MX6 Solo CPU supports only one IPU.

Содержание i.MX6 Qseven PMIC SOM



















































































Результаты поиска

Содержание i.MX6 Qseven PMIC SOM

Отзывы:

Похожие инструкции для i.MX6 Qseven PMIC SOM

Бренды по названию

Популярные бренды

iWave i.MX6 Qseven PMIC SOM, Руководство пользователя по оборудованию

Результаты поиска

Содержание i.MX6 Qseven PMIC SOM

Отзывы:

Похожие инструкции для i.MX6 Qseven PMIC SOM

Бренды по названию

Популярные бренды