IWAKI WALCHEM MDH-400 Series Скачать руководство пользователя страница 1

Страница: 1 / 33

Open the package and check that the product conforms to your order. Also, check each of the following
points. For any problem or inconsistency, contact your distributor at once.

1. Check that the model number and the HP indicated on the nameplate conform to the specifications of your

order.

2. Check that all the accessories you ordered are included.

3. Check that the pump body and parts have not been accidentally damaged or that any bolts or nuts have not

been loosened in transit.

Thank you for selecting an Iwaki Walchem MDH-(F) Series magnetic drive pump. This

instruction manual explains the correct handling, maintenance, inspection and troubleshooting

procedures for your pump. Please read through it carefully to ensure the optimum performance,

safety and long service of your pump.

Unpacking and Inspection

Fig. 1

MODEL MDH-F

HEAD (FT.)

CAPACITY (GPM)

SERIAL NO.

HOLLISTON, MA 01746

IWAKI WALCHEM

60 Hz.

RPM

Содержание MDH-400 Series


































Результаты поиска

Содержание MDH-400 Series

Отзывы:

Похожие инструкции для MDH-400 Series

Бренды по названию

Популярные бренды

IWAKI WALCHEM MDH-400 Series, Инструкция по эксплуатации

Результаты поиска

Содержание MDH-400 Series

Отзывы:

Похожие инструкции для MDH-400 Series

Бренды по названию

Популярные бренды