background image

- 2 -

●   Damaged pump.

  

Never operate a damaged pump.  A damaged pump may 
cause leakage or electrical shock.

●   Operating site must be free of water and 

humidity.

  

The pump is not designed to be water-proof or dust-proof.  
The use of the pump in places where water splashes or 
humidity is high may result in an electrical shock or short 
circuit.

●  Do not damage or change power cable.

 

  Do not scratch, damage, process, or pull the power cable 
forcibly.  An extra load onto the cable, such as heating the 
cable or placing something heavy on the cable, may dam-
age the cable and finally cause a fire or an electrical shock.

●  Do not cover the motor.

  

Running a covered motor may accumulate heat inside the 
motor and cause a fire or a mechanical failure.  Ventilate 
the motor sufficiently.

●  Arrange grounding.

  

Do not operate the pump without connecting the grounding 
wire.  Otherwise, an electrical shock may result.  Make 
sure the grounding wire is connected with the grounding 
terminal.

●  Install an earth leakage breaker (option).

  

The operation of a pump without using an earth leakage 
breaker may cause an electrical shock.  Please purchase an 
optional leakage breaker and install in the system.

●  Power cable cannot be replaced.

  

Never use a damaged or affected power cable.  Otherwise, 
a fire or an electrical shock may result.  Handle the power 
cable carefully, as it cannot to be replaced with a new 
cable.  (The pump unit itself must be replaced in that cir-
cumstance.)

●  Limited operating site and storage.

  

Do not install or store the pump in the following places:

 

*  Places where a flammable gas or material is used or 

stored.

 

*  Places where the ambient temperature is extremely high 

(40

º

C or higher) or extremely low (0

º

C or lower).

●  Do not drain the liquid in the site.

  

The liquid discharged out of the pump, including a hazard-
ous chemical liquid, must be drained into a special con-
tainer.  Never drain such liquid directly onto the floor in or 
near the operation site.

●  Disposal of used pump.

  

Disposal of used or damaged pumps must be done in 
accordance with the relevant local laws and regulations.  
(Consult a licensed industrial waste products disposing 
company.)

●  Electromagnetic precautions.

  

This product is not protected against an electromagnetic 
field. Take appropriate measures as necessary.

Caution

Caution

Prohibited

Prohibited

Prohibited

Prohibited

Caution

Caution

Electrical Shock

Grounding

Содержание MDG-R

































Отзывы: