IWAKI PUMPS EHN-B11-NAE Скачать руководство пользователя страница 55

Страница: 55 / 68

aint

ena
nc

Diaphragm replacement

Necessary tools

• An adjustable wrench or spanner

• A hexagon wrench

• A torque wrench

NOTE

Pay attention not to loose diaphragm spacers. A few diaphragm spacers may be inserted between the
retainer and plunger for the adjustment of a diaphragm location. Note that the number of diaphragm spacers
provided varies at different pumps.

Run the pump and set the stroke length to 0%. Then stop the pump.

Loosen the fitting nuts and remove the suction tube, dis-

charge tube, and air bleed tube.

Remove the pump head with a hexagon wrench.

Unscrew the diaphragm from the plunger (pump shaft).

Slide the retainer and diaphragm spacer(s) onto

the screw of the new diaphragm.

Plunger

Diaphragm spacer

Diaphragm

Retainer

Wear part replacement

Fitting nut

Air bleed tube

Discharge tube

Suction tube

Pump head

Содержание EHN-B11-NAE





































































Результаты поиска

Содержание EHN-B11-NAE

Отзывы:

Похожие инструкции для EHN-B11-NAE

Бренды по названию

Популярные бренды

IWAKI PUMPS EHN-B11-NAE, Руководство пользователя

Результаты поиска

Содержание EHN-B11-NAE

Отзывы:

Похожие инструкции для EHN-B11-NAE

Бренды по названию

Популярные бренды