IVT 09LR-N Скачать руководство пользователя страница 1

Страница: 1 / 64

SERVICE MANUAL

12LRN

Parts marked with "

" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the

safety and performance of the set.

This document has been published to be used for
after sales service only.
The contents are subject to change without notice.

CHAPTER 1. SPECIFICATION

[1] SPECIFICATION ...........................................1-1
[2] EXTERNAL

DIMENSION ..............................1-3

[3] WIRING

DIAGRAM .......................................1-4

[4] ELECTRICAL

PARTS....................................1-4

CHAPTER 2. EXPLAMATION OF CIRCUIT AND OP-
ERATION

[1] BLOCK

DIAGRAMS ......................................2-1

[2] MICROCOMPUTER CONTROL SYSTEM

........2-3

[3] FUNCTION ....................................................2-7
[4] OPERATION

MANUAL................................2-16

CHAPTER 3. FUNCTION AND OPERATION OF PRO-
TECTIVE PROCEDURES

[1] PROTECTION

DEVICE FUNCTIONS AND

OPERATIONS ...............................................3-1

[2] AIR TO AIR HEAT PUMP OPERATION IN

THERMISTOR ERROR.................................3-3

[3] THERMISTOR TEMPERATURE CHAR-

ACTERISTICS...............................................3-5

[4] HOW TO OPERATE THE OUTDOOR

UNIT INDEPENDENTLY ...............................3-6

[5] GENERAL

TROUBLESHOOTING

CHART

........ 3-6

[6] MALFUNCTION (PARTS) CHECK METH-

OD.................................................................. 3-8

[7] OUTDOOR UNIT CHECK METHOD ............3-11
[8] TROUBLESHOOTING

GUIDE .................... 3-14

CHAPTER 4. REFRIGERATION CYCLE

[1] FLOW FOW REFRIGERANT ........................ 4-1
[2] STANDARD

CONDITION .............................. 4-1

[3] TEMPERATURE AT EACH PART AND

PRESSURE IN 3-WAY VALVE....................... 4-1

[4] PERFORMANCE

CURVES ........................... 4-2

CHAPTER 5. DISASSEMBLY PROCEDURE

[1] INDOOR

UNIT ............................................... 5-1

[2] THE WIRE GUARD AND THE PLASM-

CLUSTER UNIT............................................. 5-4

[3] OUTDOOR

UNIT ........................................... 5-6

Parts Guide

TopPage

CONTENTS

SPLIT TYPE

12LR-N

MODEL

In the interests of user-safety (Required by safety regulations in some
countries) the set should be restored to its original condition and only

parts

identical to those specified should be used.

AIR TO AIR HEAT PUMP

09LR-N

Содержание 09LR-N

































































Результаты поиска

Содержание 09LR-N

Отзывы:

Похожие инструкции для 09LR-N

Бренды по названию

Популярные бренды

IVT 09LR-N, Руководство по обслуживанию

Результаты поиска

Содержание 09LR-N

Отзывы:

Похожие инструкции для 09LR-N

Бренды по названию

Популярные бренды