background image

 

Chapter 2 Installation Instructions 

2.1 Mounting Instructions 

 

2.1.1 Location Considerations 

 

Care should be taken when locating equipment behind the unit to ensure that AC power wiring, 

PLC output modules, contactors, starters and relays, and any other source of electrical 

interference are located away from the back of the unit. 

 

Particular note should be taken to the position of variable speed drives and switching power 

supplies. Their input and load cables should be screened to a central star earth point. 

 

2.1.2 Making a NEMA-4 Mounting 

Panel Details 

The unit can be mounted into panels with a depth of 1.72”(51mm).   

It is recommended that the unit be mounted on the front panel of a 

steel enclosure, through an appropriate opening*. Allow a clearance 

of 1”(25mm) around the sides of the unit for mounting hardware. 

Allow clearance for cable connections to the back of the unit. Unit 

depth may vary according to cable type used. Typically, plan a depth 

to accommodate at least 1.72”(51mm) behind the panel. 

NEMA-4 

Mounting 

Put the unit through the panel cut out. Slide the clamps into the 6 

holes provided around the case. Tighten the clamping screws in an 

even pattern until the unit is secured in the panel. 

Caution! 

Do not over tighten mounting clamps! 

Note: 

Specifications Note: 

To seal to NEMA-4 specifications, all supplied mounting clamps 

must be used and panel cannot flex more than 0.010”. 

 

 

 

 

2.1.3 Environmental Considerations 

 

The NP-612S are to be used indoors as built in displays. Make sure that the displays are 

Содержание NP-612S




































Отзывы: