IV Produkt ThermoCooler HP 100 страница 10 Скачать руководство пользователя

Страница: 10 / 20

Page 10

Operation and Maintenance

ThermoCooler HP

DSTCH.191101.01.EN

Continuous product development may give rise to specification changes without notice.

Wiring instructions

3.1 Power supply

The reversible heat pump is powered separately as shown in the diagram below.
For the recommended fuse protection, see "7 Technical data" page 19

N
PE

L2
L3

2
4
6

MS1

1
3
5

POWER SUPPLY

3×400V~50Hz

NB!

A residual current circuit breaker should not be used since the unit has

a built-in frequency inverter.

In the event that the decision is nevertheless made to use a residual current

circuit breaker, we recommend a 300 mA, type B residual current circuit breaker

specially adapted for the frequency converter.

A 300 mA, type B residual current circuit breaker offers fire protection – not

personal protection.

3.2 Communication with Climatix

Communication with the air handling unit’s (Envistar Flex) Climatix control

system takes place via Modbus. The connection between Carel and Climatix is

made using a pre-installed quick connector.

Carel

Modbus

Thermo-

Cooler HP

–

GND

Climatix

RS485

B-

A+

REF

Envistar Flex

control cabinet

Green
Yellow
Grey

Basic diagram showing communication between Carel and Climatix via Modbus

Содержание ThermoCooler HP 100





















Результаты поиска

Содержание ThermoCooler HP 100

Отзывы:

Похожие инструкции для ThermoCooler HP 100

Бренды по названию

Популярные бренды

IV Produkt ThermoCooler HP 100, Эксплуатация и обслуживание

Результаты поиска

Содержание ThermoCooler HP 100

Отзывы:

Похожие инструкции для ThermoCooler HP 100

Бренды по названию

Популярные бренды