manualshive.com logo in svg

ITW Transtech AERO 60, Руководство по эксплуатации, Страница: 5 / 56

Поделиться
Скачать
ITW Transtech AERO 60 Скачать руководство пользователя страница 5

AERO 60/90

  2 Color System

 

Release 1.0 

 PAGE 5

1.1. 

Safety 

1.1.1

 Symbols and their Interpretations 

WARNING 

Neglecting a safety instruction identified with the WARNING symbol may 

lead to personal injury

. 

CAUTION Neglecting a safety instruction identified with the CAUTION symbol may 

lead to property damage. 

POINTER It is strongly recommended to observe instructions identified with a 

POINTER symbol. 

1.1.2 

Liability 

•

In no event will 

ITW TRANS TECH 

be responsible or liable for indirect or

consequential damages resulting from the use of this equipment.

•

The information contained in this manual is subject to change due to

improvements in design.

•

Though this document has been checked for inaccuracies, 

ITW TRANS

TECH 

does not assume responsibility for any errors contained herein.

•

This manual is provided as an aid when operating the Aero 60/90 pad

printing machine. Prior to operation, it is strongly advised that the user be

thoroughly familiar with this manual.

•

ITW TRANS TECH 

is not responsible or liable for any disadvantage

occurred for not following the operating instructions.

All operators must be sufficiently trained.

 

Содержание Transtech AERO 60

























































Отзывы:

Нет отзывов