ITT Goulds Pumps IC Скачать руководство пользователя страница 78

Страница: 78 / 97

•

Make sure the O-ring surface is clean.

Oil seal replacement

Replace the oil seal if it has cuts or cracks.

Gaskets, O-rings, and seats replacement

WARNING:

Risk of death or serious injury. Leaking fluid can cause fire and/or burns. Replace all gas-
kets and O-rings at each overhaul or disassembly.

Fasteners

WARNING:

Risk of serious personal injury or property damage. Fasteners such as bolts and nuts are
critical to the safe and reliable operation of the product. Ensure appropriate use of fasten-
ers during installation or reassembly of the unit.

•

Use fasteners of the proper size and material only.

•

Replace all corroded fasteners.

•

Ensure that all fasteners are properly tightened and that there are no missing fasten-
ers.

6.5.2 Shaft and sleeve replacement guidelines

Straightness check

210

Figure 45: Straightness check

Replace the shaft (210) if runout exceeds the values in this table:

Shaft and sleeve check

524

Figure 46: Shaft and sleeve check

•

Check the shaft and sleeve (524) surface for grooves and pitting.

•

Replace the shaft and sleeve if any grooves or pits are found.

6.5.3 Bearing-frame inspection

Checklist

Check the bearing frame for these conditions:

•

Visually inspect the bearing frame and frame foot for cracks.

•

Check the inside surfaces of the frame for rust, scale, or debris. Remove all loose and foreign
material.

6.5 Pre-assembly inspections

Model IC, ICI, ICH, ICIH Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps IC


































































































Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды

ITT Goulds Pumps IC, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps IC

Отзывы:

Похожие инструкции для Goulds Pumps IC

Бренды по названию

Популярные бренды