ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя | Manualshive

Страница: 22 / 178

background image

•

The CV 3196 is available with a stuffing-box cover designed for a packing and a BigBore or a Ta-
perBore PLUS seal chamber.

Optional seal

•

a dynamic seal is available which uses a repeller to pump liquid out of the stuffing box while the
pump operates. A static seal prevents leakage when the pump is shut down.

Table 5: Power end

This table describes the main parts of the power end.

Part

Description

Frame adapter

The ductile iron frame adapter has

•

a machined rabbet fit to the seal chamber/ stuffing box cover

•

a precision dowel pin fit to the bearing frame.

Power end

•

Flood-oil lubrication is standard.

•

Oil-mist, regreasable and greased-for-life options are available.

•

The oil level is checked through a sight glass.

•

The power end is sealed with labyrinth seals.

•

The power end is made in the following sizes:

•

STi

•

MTi

•

LTi

•

XLT-i

Shaft

The shaft is available with or without a sleeve.

Bearings

The inboard bearing

•

carries only radial loads.

•

is free to float axially in the frame.

•

is a single-row deep-groove ball bearing

The outboard bearing

•

is shouldered and locked to the shaft and housing to enable it to carry radial and thrust
loads.

•

is a double-row angular-contact bearing, except for the LTi which uses a pair of single-
row angular-contact ball bearings mounted back-to-back.

3.2 General description i-ALERT

®

2 Equipment Condition Monitor

Description

The i-ALERT

®

2 Equipment Condition Monitor is a compact, battery-operated monitoring device that con-

tinuously measures the vibration and temperature of the pump power end. The i-ALERT

®

2 sensor uses

blinking red LEDs and wireless notification to alert the pump operator when the pump exceeds vibration
and temperature limits. This allows the pump operator to make changes to the process or the pump be-
fore a catastrophic failure occurs. The Condition Monitor is also equipped with a single green LED to in-
dicate when it is operational and has sufficient battery life. (i-ALERT

®

2 Bluetooth Equipment Condition

Monitor option available. The i-ALERT

®

2 monitor allows customers to identify potential problems before

they become costly failures. It tracks vibration, temperature and run-time hours and wirelessly syncs the
data with a smart phone or tablet the i-ALERT

®

2 mobile app. More information available on

More information available on

http://www.ittproservices.com/aftermarket-products/monitoring/i-alert2/i-

3.2 General description i-ALERT®2 Equipment Condition Monitor

20

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
20
21
22
23
24
...
»

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренд: Davey Страницы: 16

Бренд: Lavor Страницы: 108

Бренд: PAPILLON Страницы: 22

Aquarea WH-ADC0309J3E5B

Бренд: Panasonic Страницы: 40

Бренд: Calpeda Страницы: 43

Бренд: Dux Страницы: 20

Бренд: TradeQuip Страницы: 8

Electric iSUP Air Pump

Бренд: Bluefin SUP Страницы: 21

Бренд: ICI Caldaie Страницы: 48

Бренд: VONROC Страницы: 60

Бренд: ELCOS Страницы: 8

Бренд: Virax Страницы: 52

Бренд: MARNEX Страницы: 28

HOF14AFRQ 1F Series

Бренд: Halsey Taylor Страницы: 4

Бренд: Western Shelter Systems Страницы: 2

XC Filter Cartridge EV9613-09

Бренд: Everpure Страницы: 2

Бренд: Barmesa Pumps Страницы: 10

Бренд: YAMADA Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды