ITT GOULDS PUMPS 3410 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 84

background image

1

30° max

1.

Nylon sling, chain, or wire rope

Figure 5: The proper lifting method for a vertical pump mounted on a half pedestal

1

30° max

1.

Nylon sling, chain, or wire rope

Figure 6: The proper lifting method for a vertical pump mounted on a full pedestal

2.3 Storage guidelines

2.3.1 Pump storage requirements

Storage requirements depend on the amount of time that you store the unit. The normal packaging is
designed only to protect the unit during shipping.

Length of time in storage

Storage requirements

Upon receipt/short-term (less than six
months)

•

Store in a covered and dry location.

•

Store the unit free from dirt and vibrations.

Long-term (more than six months)

•

Store in a covered and dry location.

•

Store the unit free from heat, dirt, and vibrations.

•

Rotate the shaft by hand several times at least every three months.

Treat bearing and machined surfaces so that they are well preserved. Refer to drive unit and coupling
manufacturers for their long-term storage procedures.

You can purchase long-term storage treatment with the initial unit order or you can purchase it and apply
it after the units are already in the field. Contact your local ITT sales representative.

2.3 Storage guidelines

18

Model 3410 Installation, Operation, and Maintenance Manual

«
...
18
19
20
21
22
...
»

Содержание GOULDS PUMPS 3410





















































































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3410

Бренд: T.I.P. Страницы: 66

Бренд: Watts Страницы: 8

Бренд: Gardena Страницы: 17

Summit Pumper Vacuum

Бренд: Alto Страницы: 6

Бренд: Bard Страницы: 27

Бренд: A.O. Smith Страницы: 28

Pro VSPHP270JEP

Бренд: Jandy Страницы: 20

ARO 66605J- Series

Бренд: Ingersoll-Rand Страницы: 8

Бренд: RainPoint Страницы: 32

Sandpiper Signature Series

Бренд: Idex Страницы: 18

SCM 4 PLUS 115/92

Бренд: Flotec Страницы: 22

Inverboost Premium 10kW

Бренд: AQS Страницы: 49

Marvair MAA1020H

Бренд: ACS Страницы: 61

ISMATEC ISM 940

Бренд: Fisher Bioblock Scientific Страницы: 41

Бренд: Samoa Страницы: 12

Бренд: Evergush Страницы: 4

Бренд: GORMAN-RUPP Страницы: 44

Бренд: ACPro Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды