ITOH DENKI Power Moller CBM-105FN1-EU1, Техническая документация инструкция

Страница: 26 / 29

26
CBM-105FP1-EU1
CBM-105FN1-EU1
T
ECHNICAL
D
OCUMENTATION
Original notice - T1.3
Error signal input
Motorized
roller
condition
Cause /
symptom
Signal reset
Motorized roller
restart
SW1-4
ON
SW1-4
OFF
No signal
6LJQDO
sending
n.a.
No signal No signal 6WRSSHG No power &RQQHFWWKH9'&SRZHUVXSSO\ 6WDQGDUGVWDUWXS
6LJQDO
sending
No signal 6WRSSHG
Circuit board
damaged 5HPRYHSRZHUWKHQUHSODFHWKHFLUFXLW
board.
6WDQGDUGVWDUWXS
6LJQDO
sending
No signal 6WRSSHG
Thermister error
PLQXWHDIWHUGURSVEHORZWKHWKHUPDOWULSWKUHVKROGWKHLQMHFWLRQ
VLJQDO581
D 6723 D 581RQWHUPLQDORI&1UHPRYHVWKHHUURU
signal and restarts the motorized roller at the same time.
1 minute after drops below the thermal trip
WKUHVKROGWKHLQMHFWLRQVLJQDO2)) D ON
D 2))RQWHUPLQDORI&1RQO\UHPRYHV
the error signal, without restarting the
motorized roller.
,QMHFWLRQVLJQDO
581 D 6723 D 581
on terminal 1 of CN2
Re-connect the
disconnected
RUSRRUO\
connected CN3.
5HPRYHSRZHUDQGSURSHUO\FRQQHFWWKH
motorized roller.
6WDQGDUGVWDUWXS
6LJQDO
sending
No signal 6WRSSHG
The motorized
UROOHULVMDPPHG
for more than
4 seconds. (1)
7KHLQMHFWLRQVLJQDO581 D 6723 D 581RQWHUPLQDORI&1UHPRYHV
the error signal and restarts the motorized roller at the same time.
,QMHFWLRQVLJQDO2)) D ON D OFF terminal 2
RI&1VLJQDORQO\UHPRYHVWKHHUURUVLJQDO
without restarting the motorized roller.
,QMHFWLRQVLJQDO
581 D 6723 D 581
on terminal 1 of CN2
6LJQDO
sending
No signal 6WRSSHG
,QSXWYROWDJH
LQVXI¿FLHQW
9'&
8QGHUFDSDFLW\
of the 24 VDC
SRZHUVXSSO\
Cable cross-
section too low.
)LUVWVHFXULQJVXSSO\YROWDJHDERYH9'&7KHLQMHFWLRQVLJQDO581
D 6723 D 581RQWHUPLQDORI&1UHPRYHVWKHHUURUVLJQDODQG
restarts the motorized roller at the same time.
6HFXULQJWKHVXSSO\YROWDJHDERYH9'&
,QMHFWLRQVLJQDO2))
D ON D OFF on
WHUPLQDORI&1VLJQDORQO\UHPRYHVWKH
error signal, without restarting the motorized
roller.
,QMHFWLRQVLJQDO
581 D 6723 D 581
on terminal 1 of CN2
6LJQDO
sending
No signal 6WRSSHG
,QGXFHGYROWDJH
2YHUYROWDJH
of more than
40 V dc for 2 s
or more than
60 V dc for 0.1 s
on the power
VXSSO\
$IWHUORZHULQJWKHYROWDJHRIWKHPRWRUL]HGUROOHUEHORZ9'&WKH
LQMHFWLRQVLJQDO581
D
6723
D
581RQWHUPLQDORI&1UHPRYHV
the error signal and restarts the motorized roller at the same time.
$IWHUORZHULQJWKHYROWDJHRIWKHPRWRUL]HG
UROOHUEHORZ9'&WKHLQMHFWLRQVLJQDO
OFF
D
ON
D
OFF on terminal 2 of CN2
VLJQDORQO\UHPRYHVWKHHUURUVLJQDOZLWKRXW
restarting the motorized roller.
,QMHFWLRQVLJQDO
581
D
6723
D
581
on terminal 1 of CN2
)RUVHFRQGVDIWHUSRZHULQJRQDQGVDIWHUWKHSRZHUIDLOXUHWKH/('OLJKWVXSEULHÀ\,JQRUHWKHVHHUURU
signals.
,QWKHHYHQWRIWKHPRWRUL]HGUROOHUMDPPLQJLWMHUNVWRUHOHDVHWKHORDG,IWKHSUREOHPODVWVORQJHUWKDQ
4 seconds, the motorized roller stops and the circuit board is set to fault mode.
$QRYHUYROWDJHPD\EHFDXVHGE\PDNLQJWKHPRWRUL]HGUROOHUWXUQDWPRUHWKDQRIWKHVHWVSHHGORDG
SXVKHGPDQXDOO\IRUH[DPSOH
7KHHUURUVLJQDOFDQEHUHPRYHGE\UHPRYLQJSRZHUIRUPRUHWKDQVHFRQGV