ITech IT-M7700 Series Скачать руководство пользователя страница 63

Страница: 63 / 126

SOURce Subsystem(IT-M7700)

Note

This command is a special command of IT-M7723.

The response time of this command is at least greater than 100ms.

[SOURce:]NORMal:WAVE

This command is used to set the wave.

Syntax

[SOURce:]NORMal:WAVE

<0|1|2|3|4|SINE|SQUA|TRIANGLE|SAW|CLIPSINE>

Arguments

：

<0|1|2|3|4|SINE|SQUA|TRIANGLE|SAW|CLIPSINE>

Query Syntax

：

[SOURce:]NORMal:WAVE?

Returns

：

<SINE|SQUA|TRIANGLE|SAW|CLIPSINE>

[SOURce:]NORMal:WAVE:THD

This command is used to set the THD.

Syntax

[SOURce:]NORMal:WAVE:THD <NR1>

Arguments

：

<NR1> 1~30 => THD1~THD30

Query Syntax

：

[SOURce:]NORMal:WAVE:THD?

Returns

：

<String> THD1~THD30

[SOURce:]NORMal:WAVE:USER

This command is used to set the USER wave.

Содержание IT-M7700 Series































































































































Результаты поиска

Содержание IT-M7700 Series

Отзывы:

Бренды по названию

Популярные бренды

ITech IT-M7700 Series, Руководство по программированию

Результаты поиска

Содержание IT-M7700 Series

Отзывы:

Бренды по названию

Популярные бренды