Italforni TS Gas Скачать руководство пользователя страница 5

                                                                                      

Instructions for use and maintenance

 

 

 

 

1.1 General warnings 
 

 

Read  this  booklet  carefully  as  it  provides  directions  on  safety  for  the  oven  use  and  maintenance.  The 
purpose of this manual is to inform operators of the rules and essential criteria for guaranteeing their 
safety and for prolonging the working life of the oven. Before the oven is put into service this manual 
must be read by all staff authorised to work on it. 

 

 

This  instruction  booklet  must  be  kept  with  the  oven  for  future  reference.  If  the  oven  is  sold  or 
transferred,  make  sure  that  the  booklet  accompanies  it  every  time,  so  that  the  new  user  can  be 
informed of its operation and the safety warnings. It is to be kept in a place which is safe, dry and can be 
quickly located whenever it needs to be referred to. If it deteriorates or is lost, request a replacement 
copy from your nearest service centre. 

 

 

The  product  is  carefully  packed  in  sturdy  wooden  cage  with  nylon  bubble  packing  to  protect  it  from 
knoks  and  humidity  during  transportation  and  is  consigned  to  the  forwarder  in  the  best  possible 
conditions.  

However  we  would  advise  you  to  check  the  packaging  on  taking  delivery,  for  evidence  of  any  signs  of 

damage. Should they be found they must be noted on the delivery receipt to be signed by the driver. On 
unpacking the appliane, check for any signs of damage. In the event of any damage do not attempt to 
use the appliance and contact your nearest service centre. 

 

 

Put the appliance into service in accordance with the governing laws. These instructions are only valid 
for category II2H3+ tunnel pizza oven model. 

 

 

This oven is intended for the following use: cooking pizzas or similar foods. It must not be used for other 
purposes;  any  other  use  is  considered  improper.  The  appliance  is  intended  for  collective  and 
professional use and must be operated by staff trained in its use. 

 

 

Servicing, conversion to other types of gas, installation and inspection for proper working must only be 
performed by qualified persons.  

 

 

Each  time  a  new  part  is  fitted  or  a  component  adjusted,  make  sure  that  it  is  sealed  with  paint  to 
discourage any tampering. 

 

 

For all repairs, contact an authorised service centre and always insist on original spare parts. 

 

 

The following symbol denotes “hot surface”. Avoid all direct contact with such surfaces. 

 

 

Use personal protective heat equipment when using the appliance. 

 

 

When the appliance has reach the end of its working life, all its parts and components must be disposed 
separately; devide each type of material forming the oven, e.g. stainless steel parts, thermal insulation 
in ceramic fiber, refractory tiles, cables and electric devices. The disposal of such materials is regulated 
by law dispositions and EU Directives and may involve penalties in case of intentional behaviours that  
may cause harm to the environment and to the people. Every countries dispose the appliance 
complying with the national and local laws in force in the country of use.  

 
 

 

Содержание TS Gas



























Отзывы: